Switches

3 pole, 4 position (make before break) rotary switch with a ¼" solid shaft. 3P4T rotary switch.

Genuine Carling 2 Position Mini Toggle, On-On, Short Round Bat, Right Angle, PC Mount Features:

• SPDT ( Single Pole/ Double Throw) On-On switch
• 0.275" bushing length
• 0.270” bat length
• ¼" chassis hole diameter
• Right angle, PC Mount terminals

Note: On-On switches may sometimes be referred to as On-None-On.

Carling, SPDT mini toggle, 2 positions, ¼" mounting hole diameter, 0.354" bushing length.

Genuine Carling Technologies dress nuts for use with full size toggle switches and footswitches. These dress nuts feature a chamfered edge with a knurled bottom half for a unique look that is simple to tighten down. The top of the threading is capped. These fit any 15/32-32UNS bushing but can also work with some M12 bushings.

0.354" bushing length. 2-Position On/On. ¼" mounting hole diameter. Double pole/Double throw (DPDT). PC mount pins.

Premium three position DPDT mini toggle switches from Gorva Design. The Bascular Mini switches have a medium 7.5mm actuator length. These switches feature silver plated copper contacts. RoHS compliant & lead-free. Mounting hardware included. Details

• 8.89 mm bushing length
• Medium bat
• 3-Position On/On/On
• ¼" mounting hole diameter
• Double pole/Double throw (DPDT)
• Solder lugs

Features:

• Power Rating: DC9V, 1A
• Contact Resistance: <10mΩ
• Insulation Resistance: 1000MΩ Minimum
• Dielectric Strength: 1000V RMS @ Sea Level
• Operating Temperature: -40°C ~ +85°C
• Electrical Life: 40,000 Cycles
• RoHS & Lead-free

Latching DPDT footswitch, PC mount. Made in Taiwan.

Carling mini-toggle switch, SPDT, PC Pins. 2-Position.

• 0.354" bushing length
• 2-Position On/On
• ¼" mounting hole diameter
• Single pole/Double throw (SPDT)
• PC mount pins

High quality vactrols from Xvive. The Xvive vactrols are clones of the original Excelitas / Perkins-Elmer vactrols used in many effects pedals, synthesizers, compressors and other equipment. These vactrols feature a thick epoxy sealed casing. The VTL5C3 and VTL5C3/2 both have a steep slope, good dynamic range, a very low temperature coefficient of resistance, and a small light history memory.

Carling, SPST footswitch, momentary with solder lugs. Provides a compact yet rugged solution to general purpose switch needs. Alternate action, metal construction and stiff (6-8 lb) actuation force have combined to make this switch a pillar in a variety of markets.

Whether you need to replace a worn switch or just want to add a little tonal variety to your favorite instrument, Fender® offers this high quality, 3 position switch with knob and mounting hardware.

Carling, DPDT latching footswitch, On-On, with solder lugs. Provides a compact yet rugged solution to general purpose switch needs. Alternate action, metal construction and stiff (6-8 lb) actuation force have combined to make this switch a pillar in a variety of markets.

Carling, DPST toggle, 2-position, On-Off with solder lugs (3A, 125V), .500"" toggle length, 0.465" bushing length.
Note: On-Off switches may sometimes be referred to as On-None-Off.

Nickel-plated internal tooth lock washers from Carling. These fit 15/32 and M12 bushing which are commonly used on full sized toggle switches and footswitches.

Carling, DPDT 2 position toggle with solder lugs (6A, 125V). 0.687" toggle length. On-On.
Note: On-On switches may sometimes be referred to as On-None-On.

Lighted DPST On-Off power switch. Used in Marshall JCM series and others. 15/16" x 1-1/16" x 1" deep.

Carling mini-toggle switch, DPDT, 3 position, ¼" mounting hole diameter, 0.354" bushing length.

• 0.354" bushing length
• 3-Position
• ¼" mounting hole diameter
• Double pole/Double throw (DPDT)
• Solder lugs

Threaded through dress nuts for use with mini toggle switches. Unlike the other versions of this dress nut, this nut is not capped allowing the nut to thread past the top of the switch’s bushing. The uncapped top can be useful where internal depth is an issue such as parallel PCB mounting. These plated dress nuts feature a chamfered edge for a professional look and work on any 1/4-40 UNS threaded bushing. Two sides are flatted for use with a tool when fastening.

VTL5C1 vactrols for use in amplifiers, effect pedals, synthesizers and more. The VTL5C1 was commonly used for channel switching circuits in amps made by Crate and others.

Carling, DPST 2 position toggle switch, On-Off. 10A 250VAC, 15A 125VAC. Made in Mexico. Note: On-Off switches may sometimes be referred to as On-None-Off.

.3A 125 VAC. 1 pole, 12 position, solid 1/4" shaft. SP12T rotary switch.

Rubber caps / switch tips for mini toggle switches in a variety of colors. These are made for standard sized toggle bats.

SPST(single pole,single throw) normally open, Off-(On) momentary foot switch with solder lugs and soft switching. These high quality switches feature a black actuator, bushing and mounting hardware. Depressing the switch shorts the lugs together and when the switch is released it returns to its non connected state with no click.

• SPST momentary switch
• Black finish and hardware
• Soft, silent switching with no click
• Normally open operation
• Solder lugs
• Nuts and washer included
• Note: Off-(On) switches may sometimes be referred to as Off-None-(On).

Rotary impedance selector. Modern, selects between 4Ω, 8Ω, and 16Ω. Panel mount from front side. SP3T.