Switches

Switch - Carling, Toggle, SPST, On-Off, Side Solder Lugs
Carling, 2 position, On-Off, SPST with solder lugs, 1/2" mounting hole. Note: On-Off switches may sometimes be referred to as On-None-Off.
$5.15
Switch - Carling, Toggle, SPST, Replacement for Fender®
Fender® style power and/or standby switch (Single Pole, Single Throw). This latching On-Off switch is a great replacement for older Fender® amps where the shorter toggle length (1/2”) is desired.
$5.95
Switch - Fender®, Toggle, SPST, Standby, Solder Lugs
Original Fender®, Carling SPST On-Off toggle switch for Fender tube amps - 3A, 250VAC; 6A, 125VAC, ½" mounting hole. Commonly used as the power switch.
$6.95
Switch - Marshall Style, Rocker, Power for MG Amps, Black
Marshall style black On-Off rocker switch for MG amps. 0.51" x 0.76" Mounting Hole. DPST.
$6.55
Switch - Marshall, Toggle, DPST, On-Off, Chrome Tip
Marshall toggle switch, latching 2 position DPST, On-Off. 15A 250VAC rating. Used for Mains and Standby switch in Marshall 1959SLP, 1987X, 2245 and others. See Marshall nut S-HM300N if necessary. Nut sold separately. Note: On-Off switches may sometimes be referred to as On-None-Off.
$15.95
Switch - Peavey, Rocker, SPST, On-Off
Peavey SPST rocker switch, On-Off, with molded dot to indicate 'on' position, can be used in Classic VTX. 5A 125VAC, 2A 250VAC
$1.90
Switch - Rocker, Lighted Power, Used in JCM Series & Others
Lighted DPST On-Off power switch. Used in Marshall JCM series and others. 15/16" x 1-1/16" x 1" deep.
$12.50
Switch - Rocker, Round Mounting Hole, SPST, 6A, 125VAC
Rectangular rocker switch that uses a round mounting hole. This black nylon rocker switch has a small panel footprint and is easy to add to projects due to the round mounting hole. Mounting nut and lock washer included.
  • SPST
  • On-Off
  • 6A, 125VAC / 3A, 250VAC
  • 12.2mm Mounting Hole
$1.99
Switch - Rocker, Standby for JCM Series & Others, Black
For Marshall™, JCM series and others. 15/16" x 1 1/16" x 1" deep. DPST On-Off switch,
$7.95
Switch - Rotary, 1 Pole, 3 Position
High quality three position rotary switch commonly used as an impedance selector switch on tube amps. This rugged switch is rated for 6A at 125VAC and 3A at 250VAC. The flatted 6mm shaft can be used with the shaft adapter found in the accessories below to easily fit standard ¼” knobs. Mounting hardware included. SP3T.
$12.95
Switch - Rotary, Impedance Selector, 3 Position
Rotary impedance selector, 4/8/16. Body screws onto chassis hole. SP3T switch.
$16.95
Switch - Rotary, Impedance Selector, Replacement for Marshall
Rotary impedance selector. Modern, selects between 4Ω, 8Ω, and 16Ω. Panel mount from front side. SP3T.
$34.95
On Backorder
Switch - Rotary, Voltage Selector, Modern, for Marshall
  • Ratings:
    • IEC: 6.3 A / 250 VAC; 50 Hz
    • UL: 10 A / 250 VAC; 60 Hz
    • CSA: 8 A / 250 VAC; 60 Hz
  • Mounting: Panel Mount from front side
  • Fastening: Screw-on mounting
  • Terminal: Solder
  • Number of Stages: 3
  • Type: SP3T
  • Lifetime: 300 operating cycles (without load)
  • Degree of Protection: IP 40
  • Allowable Operation Temp.: -40 °C to 85 °C
  • Climatic Category: 25/85/21 acc. to IEC 60068-1
  • Material of Socket: Thermoplastic, black, UL 94V-0
  • Weight: 16.5 g
  • Solderability: 350 °C / 2 sec acc. to IEC 60068-2-20, Test Ta, method 2
  • Resistance to Soldering Heat: 350 °C / 10 sec acc. to IEC 60068-2-20, Test Tb, method 2
  • Insulation Resistance: > 10,000MΩ (500VDC; 1min)
  • Contact Resistance: < 10 mΩ at 20 mV
  • Dielectric Strength:
    • > 2.5kVAC between L-N (1min; 50Hz)
    • > 4kVAC between L/N-PE (1min; 50Hz)
  • Clearance and Creepage Distance:
    • > 5mm
    • > 8mm between L/N-PE
  • Resistance to Vibration: acc. to IEC 60068-2-6, test Fc
$35.45
Switch - Selector, Vintage Style, for Marshall, Male
Vintage style selector switch male part, replacement for Marshall.
$12.95
Switch - Switchcraft, Slide, DPTT, 3-Position
Genuine Switchcraft® DPTT 3-position slide switch for use on Mustang and Duosonic style guitars. This switch can be wired to operate in either On/Off/On or On/On/On configurations. Upgrade cheap or malfunctioning switches with these high quality replacements.
  • Recommended .75 control cavity depth
  • 1.406” center-to-center mounting hole spacing
  • #4-40 screws recommended for mounting
  • Screws not included
$5.35
Switch - Switchcraft®, Slide, DPDT, Jazzmaster / Jaguar
Genuine Switchcraft® DPDT 2-position On-On slide switch for use on Jazzmaster and Jaguar style guitars. Also used for bright switches in Fender black and silverface amplifiers. Upgrade cheap or malfunctioning switches with these high quality replacements.
  • Recommended .75 control cavity depth
  • 1.125” center-to-center mounting hole spacing
  • Latching
  • Screws not included
  • See S-HS440-12 for compatible screws
$4.45
Switch - Toggle, DPST, On-Off, Chrome Tip
Toggle switch for Marshall amps, latching 2 position DPST, On-Off. 15A 250VAC rating. Used for Mains and Standby switch in Marshall 1959SLP, 1987X, 2245 and others. Mounting nuts (1 hex and 1 knurled) included. Main features:
  • Construction : Terminal and contact support are manufactured from a single piece of metal. The contacts are resistance-welded to the terminal for increased mechanical strength.
  • Rating : These switches are suitable for motor loads and power applications up to 15A 250VAC
  • UL, CSA and NF-VDE (EN 61058-1) approved

Note: On-Off switches may sometimes be referred to as On-None-Off.
$14.95