Switches

3 pole, 4 position (make before break) rotary switch with a ¼" solid shaft. 3P4T rotary switch.

Cable-mounted inline switch (On-Off) most often used for lamps and other applications. This switch pairs with SPT-1 type power cords and features a thumbwheel actuator.

Rotary impedance selector, 4/8/16. Body screws onto chassis hole. SP3T switch.

Rotary impedance selector. Modern, selects between 4Ω, 8Ω, and 16Ω. Panel mount from front side. SP3T.

• Ratings:
  
  • IEC: 6.3 A / 250 VAC; 50 Hz
  • UL: 10 A / 250 VAC; 60 Hz
  • CSA: 8 A / 250 VAC; 60 Hz
• Mounting: Panel Mount from front side
• Fastening: Screw-on mounting
• Terminal: Solder
• Number of Stages: 3
• Type: SP3T
• Lifetime: 300 operating cycles (without load)
• Degree of Protection: IP 40
• Allowable Operation Temp.: -40 °C to 85 °C
• Climatic Category: 25/85/21 acc. to IEC 60068-1
• Material of Socket: Thermoplastic, black, UL 94V-0
• Weight: 16.5 g
• Solderability: 350 °C / 2 sec acc. to IEC 60068-2-20, Test Ta, method 2
• Resistance to Soldering Heat: 350 °C / 10 sec acc. to IEC 60068-2-20, Test Tb, method 2
• Insulation Resistance: > 10,000MΩ (500VDC; 1min)
• Contact Resistance: < 10 mΩ at 20 mV
• Dielectric Strength:
  
  • > 2.5kVAC between L-N (1min; 50Hz)
  • > 4kVAC between L/N-PE (1min; 50Hz)
• Clearance and Creepage Distance:
  
  • > 5mm
  • > 8mm between L/N-PE
• Resistance to Vibration: acc. to IEC 60068-2-6, test Fc

Vintage style selector switch male part, replacement for Marshall.

Switchcraft 3 Position Pickup Selector, replacement for Gibson L-Type. Similar to Gibson®. As found on 335 hollow body style guitars as well as thinner solid bodies such as the Gibson SG.
Tip not included, see W-SC-W0X

Nickel Finish

Switchcraft 3 Position Pickup Selector, replacement for Gibson L-Type. Similar to Gibson®. As found on 335 hollow body style guitars as well as thinner solid bodies such as the Gibson SG.

• Tip not included. See W-SC-W0X (Note: Two threads will show beneath the switch cap.)
• Nickel Finish

Switchcraft 3 Position Pickup Selector, Replacement for Gibson L-Type. Similar to Gibson® P-SW01. As found on 335 hollow body style guitars as well as thinner solid bodies such as the Gibson SG. Features a slightly longer (3/8”) bushing ideal for thicker topped guitars.

• Tip not included. See W-SC-W0X
• Black finish

Switchcraft 3 position Pickup Selector, Replacement for Gibson L-Type. Similar to Gibson® PSTS-010. As found on 335 hollow body style guitars as well as thinner solid bodies such as the Gibson SG. This version of the L-Type switch is used in the common two pickup wiring for a neck position, middle position with neck and bridge, and a bridge position.

Switchcraft 3 position Pickup Selector, Replacement for Gibson Straight-Type. As found on LP style solid body guitars.

Genuine Switchcraft® DPTT 3-position slide switch for use on Mustang and Duosonic style guitars. This switch can be wired to operate in either On/Off/On or On/On/On configurations. Upgrade cheap or malfunctioning switches with these high quality replacements.

• Recommended .75 control cavity depth
• 1.406” center-to-center mounting hole spacing
• #4-40 screws recommended for mounting
• Screws not included

One of the most rugged and durable switches available for your Gibson Les Paul or similar two pickup guitars.

Genuine Switchcraft® DPDT 2-position On-On slide switch for use on Jazzmaster and Jaguar style guitars. Also used for bright switches in Fender black and silverface amplifiers. Upgrade cheap or malfunctioning switches with these high quality replacements.

• Recommended .75 control cavity depth
• 1.125” center-to-center mounting hole spacing
• Latching
• Screws not included
• See S-HS440-12 for compatible screws

PCB snap-in tactile switch with a 14mm height when mounted. This momentary Off-(On) SPST tactile switch has a standard 6.5mm x 4.5mm footprint.

PCB snap-in tactile switch with a 5mm height when mounted. This momentary Off-(On) SPST tactile switch has a two pin 4.5mm footprint.

PCB snap-in tactile switch with a 7mm height when mounted. This momentary Off-(On) SPST tactile switch has a standard 6.5mm x 4.5mm footprint.

PCB snap-in tactile switch with a 9.5mm height when mounted. This momentary Off-(On) SPST tactile switch has a standard 6.5mm x 4.5mm footprint.

3 position (on-off-on) heavy duty bat handle toggle switch with screw terminals. Made in USA.

• Rating: 20A 125VAC, 10A 250VAC, 3/4" HP 125 - 250VAC
• DPDT
• Mounting Hole: .50in.

Heavy duty bat handle, DPDT. Rating: 20A 125V AC, 10A 277V AC Mounts in 1/2" hole, screw connections. On-On.
Note: On-On switches may sometimes be referred to as On-None-On.

Toggle switch for Marshall amps, latching 2 position DPST, On-Off. 15A 250VAC rating. Used for Mains and Standby switch in Marshall 1959SLP, 1987X, 2245 and others. Mounting nuts (1 hex and 1 knurled) included. Main features:

• Construction : Terminal and contact support are manufactured from a single piece of metal. The contacts are resistance-welded to the terminal for increased mechanical strength.
• Rating : These switches are suitable for motor loads and power applications up to 15A 250VAC
• UL, CSA and NF-VDE (EN 61058-1) approved

Note: On-Off switches may sometimes be referred to as On-None-Off.

SPST On-Off toggle switch. Made in Taiwan (M10 x.1.0 threading) .39" bushing diameter.

Optocoupler. Vibrato LDR for Fender Amps. Fix the dead LDR-style tremolo on your vintage Fender amps as well as others.

• Non-polarized optical side is indicated by silver dot and slightly longer leads
• Resistive side is indicated only by slightly shorter leads
• This neon lamp optocoupler is commonly referred to as a roach

Rubber caps / switch tips for mini toggle switches in a variety of colors. These are made for standard sized toggle bats.