Synth & Eurorack Parts / DIY

The FatKeys™ SSI2164 is perhaps the most flexible VCA available, with four independent channels for lowest cost-per-VCA. The user-selectable mode control allows Class A, AB, or intermediate biasing, and current inputs and outputs provide great design freedom. Ideal for voltage-controlled filters. The SSI2164 is a versatile VCA building block for high-performance audio applications. Four independent channels provide voltage control of current-mode inputs and outputs for a gain range from +20dB to –100dB, with control provided by a ground-referenced –33mV/dB constant. The SSI2164 will directly retrofit existing SSM/V2164 positions while offering improvements that include significantly lower overall distortion, on-chip protection against asymmetrical power failure, and a substantial increase of input current handling. The device offers considerable flexibility for a wide range of design goals and applications.

The AS3080ED is Alfa’s version of the CA3080 IC in an SOIC package. The AS3080ED is a gain block which is the operational-transconductance-amplifier (OTA). The AS3080ED has differential input and a single-ended, push-pull, class A output. Amplifier bias input may be used either for gating or for linear gain control. High output impedance and transconductance (gM) is directly proportional to the amplifier bias current (IABC). Linearizing diodes are provided at the inputs to reduce distortion and allow higher input levels. The result is a 10-dB signal-to-noise improvement referenced to 0.5 percent THD.
The AS3080ED is notable for it’s high slew rate (50V/µs), which makes it especially useful for multiplexer and fast unity-gain voltage followers.

OP275 dual audio op amp in an 8-pin DIP package. The OP275 is the first amplifier to feature the Butler Amplifier front end. This new front end design combines both bipolar and JFET transistors to attain amplifiers with the accuracy and low noise performance of bipolar transistors, and the speed and sound quality of JFETs. Total Harmonic Distortion plus Noise equals that of previous audio amplifiers, but at much lower supply currents. A very low l/f corner of below 6 Hz maintains a flat noise density response. Whether noise is measured at either 30 Hz or 1 kHz, it is only 6 nVHz. The JFET portion of the input stage gives the OP275 its high slew rates to keep distortion low, even when large output swings are required, and the 22 V/µs slew rate of the OP275 is the fastest of any standard audio amplifier.

The NJM2120 is a dual operational amplifier of 2-INPUT and 1-OUTPUT with analog switch. The NJM2120 can be used as analog switch under the condition of GV=0dB, as Switch + Amp in order that each gain (A or B) can be adjusted independently. Each amplifier of the NJM2120 has the same electrical characteristics as the NJM4558. The NJM2120 is suitable for audio, video, electrical musical instrument, etc.

The AS194H is a junction isolated ultra well-matched monolithic NPN transistor pair with an order of magnitude improvement in matching over conventional transistor pairs. Electrical characteristics of these devices such as drift versus initial offset voltage, noise, and the exponential relationship of base-emitter voltage to collector current closely approach those of a theoretical transistor. Extrinsic base and emitter resistances are very low, giving very low noise and operating over a wide current range. To guarantee long term stability of matching parameters, internal clamp diodes have been added across the emitter-base junction of each transistor. These prevent degradation due to reverse biased emitter current, the most common cause of field failures in matched devices.

The AS194DE is a junction isolated ultra well-matched monolithic NPN transistor pair with an order of magnitude improvement in matching over conventional transistor pairs. Electrical characteristics of these devices such as drift versus initial offset voltage, noise, and the exponential relationship of base-emitter voltage to collector current closely approach those of a theoretical transistor. Extrinsic base and emitter resistances are very low, giving very low noise and operating over a wide current range. To guarantee long term stability of matching parameters, internal clamp diodes have been added across the emitter-base junction of each transistor. These prevent degradation due to reverse biased emitter current, the most common cause of field failures in matched devices.

The AS394H is a junction isolated ultra well-matched monolithic NPN transistor pair with an order of magnitude improvement in matching over conventional transistor pairs. Electrical characteristics of these devices such as drift versus initial offset voltage, noise, and the exponential relationship of base-emitter voltage to collector current closely approach those of a theoretical transistor. Extrinsic base and emitter resistances are very low, giving very low noise and operating over a wide current range. To guarantee long term stability of matching parameters, internal clamp diodes have been added across the emitter-base junction of each transistor. These prevent degradation due to reverse biased emitter current, the most common cause of field failures in matched devices.

The FatKeys™ SSI2162 provides two independent VCA channels, and like its SSI2161 and SSI2164 siblings offers great flexibility in design of dynamics processors, automatic or remote level control, and voltage controlled filters. Highly compact 10-lead SSOP package. The SSI2162 is a versatile VCA building block for high-performance audio applications. Two independent channels provide voltage control of a current-mode input and output for a gain range from +20dB to –100dB, with control provided by a ground-referenced –33mV/dB constant. The device offers considerable flexibility for a wide range of design goals and applications. A unique mode control allows selection of Class A, Class AB, or in-between using a single resistor. In addition, improved current handling allows use of lower value input resistors for reduced output noise without loss of headroom. Both channels can be parallel-connected for further noise improvement.

The AS3046 is Alfa’s version of the CA3046 IC in an SOIC package. The AS3046D consists of five general purpose silicon NPN transistors on a common monolithic substrate. Two of the transistors are internally connected to form a differentially-connected pair. The transistors are well suited to a wide variety of applications in low power systems. They may be used as discrete transistors in conventional circuits however, in addition, they provide the very significant inherent integrated circuit advantages of close electrical and thermal matching. The AS3046D is available in a 14-pin SOIC package. Features

• Matched pair of npn transistors
• VBE matched less than ±1 mV
• 5 general purpose monolithic transistors
• Wide operating current range

Applications

• Filters
• Custom designed differential amplifiers
• Temperature compensated amplifiers

A very high performance single-channel VCA for the most demanding applications, the ProCircuit™ SSI2161 offers industry-leading lowest-noise, and a mode control to optimize noise vs. distortion performance. All at low-cost and in a 10-lead SSOP package. The SSI2161 is a versatile VCA building block for high-performance audio applications. A single channel provides voltage control of current-mode inputs and outputs for a gain range from +20dB to –100dB, with control provided by a ground-referenced –33mV/dB constant. The device offers considerable flexibility for a wide range of design goals and applications. A unique mode control allows selection of Class A, Class AB, or in-between using a single resistor. In addition, improved current handling allows use of lower value input resistors for reduced output noise without loss of headroom.

The LM13700 series consists of two current controlled transconductance amplifiers, each with differential inputs and a push-pull output. The two amplifiers share common supplies but otherwise operate independently. Linearizing diodes are provided at the inputs to reduce distortion and allow higher input levels. The result is a 10-dB signal-to-noise improvement referenced to 0.5 percent THD. High impedance buffers are provided which are especially designed to complement the dynamic range of the amplifiers. The output buffers of the LM13700 differ from those of the LM13600 in that their input bias currents (and thus their output DC levels) are independent of IABC.

LT1054 switched-capacitor voltage converter with regulator in an 8 pin DIP package. The LT1054 device is a bipolar, switched-capacitor voltage converter with regulator. It provides higher output current and significantly lower voltage losses than previously available converters. An adaptive-switch drive scheme optimizes efficiency over a wide range of output currents. Total voltage drop at 100-mA output current typically is 1.1 V. This applies to the full supply-voltage range of 3.5 V to 15 V. Quiescent current typically is 2.5 mA. The LT1054 also provides regulation, a feature previously not available in switched-capacitor voltage converters. By adding an external resistive divider, a regulated output can be obtained. This output is regulated against changes in both input voltage and output current. The LT1054 can also shut down by grounding the feedback terminal.

OPA134 single op amp in an 8-pin DIP package. The OPA134 series are ultra-low distortion, low-noise operational amplifiers fully specified for audio applications. A true FET input stage is incorporated to provide superior sound quality and speed for exceptional audio performance. This, in combination with high output drive capability and excellent DC performance, allows for use in a wide variety of demanding applications. In addition, the OPA134 has a wide output swing, to within 1 V of the rails, allowing increased headroom and making it ideal for use in any audio circuit. The OPA134 SoundPlus™ audio operational amplifiers are easy to use and free from phase-inversion and the overload problems often found in common FET-input operational amplifiers. They can be operated from ±2.5-V to ±18-V power supplies.

TC1044 charge pump voltage converter in an 8 pin DIP package. The TC1044S is a pin-compatible upgrade to the Industry standard TC7660 charge pump voltage converter. It converts a +1.5V to +12V input to a corresponding –1.5V to –12V output using only two low cost capacitors, eliminating inductors and their associated cost, size and EMI. Added features include an extended supply range to 12V, and a frequency boost pin for higher operating frequency, allowing the use of smaller external capacitors. The on-board oscillator operates at a nominal frequency of 10kHz. Frequency is increased to 45kHz when pin 1 is connected to V+.

The BA4560, is a dual operational amplifiers which achieves approximately twice the high output current of the BA4558, as well as featuring a higher slew rate of 4V / µs, a gain band width of 10MHz, and an improved frequency characteristic. 8-pin DIP package.

TLC274 quad op amp in a 14-pin DIP package. The TLC274 quad operational amplifier combines a wide range of input offset voltage grades with low offset voltage drift, high input impedance, low noise, and speeds approaching that of general-purpose BiFET devices. These devices use Texas Instruments silicon- gate LinCMOSTM technology, which provides offset voltage stability far exceeding the stability available with conventional metal-gate processes. The extremely high input impedance, low bias currents, and high slew rates make these cost-effective devices ideal for applications which have previously been reserved for BiFET and NFET products.

LM380 power amp in a 14-pin DIP package. The LM380 is a power audio amplifier for consumer applications. In order to hold system cost to a minimum, gain is internally fixed at 34 dB. A unique input stage allows ground referenced input signals. The output automatically self-centers to one-half the supply voltage. The output is short circuit proof with internal thermal limiting. The package outline is standard dual-in-line. The LM380N uses a copper lead frame. The center three pins on either side comprise a heat sink.

The AS301AN is Alfa’s version of the LM301A in an 8 pin DIP package. The AS301A is a general purpose operational amplifier. This amplifier offers many features which make its application nearly foolproof: overload protection on the input and output, no latch-up when the common mode range is exceeded, and freedom from oscillations and compensation with a single 30 pF capacitor. It has advantages over internally compensated amplifiers in that the frequency compensation can be tailored to the particular application. For example, in low frequency circuits it can be overcompensated for increased stability margin. Or the compensation can be optimized to give more than a factor of ten improvements in high frequency performance for most applications. In addition, the device provides better accuracy and lower noise in high impedance circuitry.

PT2399 echo/delay chip used in many DIY and commercial pedals. The PT2399 is in a DIP 16 package. Minimal external components are required for use and delay time is set with resistance.

LM386 Low Voltage Audio Power Amplifier The LM386 is a mono low voltage amplifier that can be used in a variety of applications. It can drive loads from 4 Ω to 32 Ω. The gain is internally set to 20 but it can be modified from 20 to 200 by placing a resistor and capacitor between pins 1 and 8. As this is an Op Amp it can be used in different configurations to fit in several applications. The internal gain setting resistor allows the LM386 to be used in a very low part count system. In addition a series resistor can be placed between pins 1 and 5 to modify the gain and frequency response for specific applications. These are found in many small audio amplifiers and even tiny pedal sized guitar amplifiers! There are tons of possibilities for this little Op Amp.

OP07 precision op amp in an 8-pin DIP package.These devices offer low offset and long-term stability by means of a low-noise, chopperless, bipolar-input-transistor amplifier circuit. For most applications, external components are not required for offset nulling and frequency compensation. The true differential input, with a wide input-voltage range and outstanding common-mode rejection, provides maximum flexibility and performance in high-noise environments and in noninverting applications. Low bias currents and extremely high input impedance are maintained over the entire temperature range.

Low noise JFET quad operational amplifier. Incorporates well matched, high-voltage JFET and bipolar transistors in a monolithic integrated circuit. Features high slew rates, low input bias and offset currents, and low offset voltage temperature coefficients. Features:

• Wide common-mode and differential voltage range
• Low input bias and offset current
• Low noise en = 15 nV/HZ
• Output short-circuit protection
• High input impedance JFET input stage
• Low harmonic distortion: 0.01%
• Internal frequency compensation
• Latch up free operation
• High slew rate: 16 V/us (typical)

CD4046B CMOS Micropower Phase-Locked Loop (PLL) consists of a low-power, linear voltage-controlled oscillator (VCO) and two different phase comparators having a common signal-input amplifier and a common comparator input. A 5.2-V zener diode is provided for supply regulation if necessary. Features:

• Very low power consumption: 70 µW (typ.) at VCO fo = 10 kHz, VDD = 5 V
• Operating frequency range up to 1.4 MHz (typ.) at VDD = 10 V, RI = 5 k
• Low frequency drift: 0.04%/°C (typ.) at VDD = 10 V
• Choice of two phase comparators:
  
  • Exclusive-OR network (I)
  • Edge-controlled memory network with phase-pulse output for lock indication (II)
• High VCO linearity: <1% (typ.) at VDD = 10 V
• VCO inhibit control for ON-OFF keying and ultra-low standby power consumption
• Source-follower output of VCO control input (Demod.

LM1458 dual op amp in an 8-pin DIP package. The LM1458 is a general purpose dual operational amplifier. The two amplifiers share a common bias network and power supply leads. Otherwise, their operation is completely independent. Features

• No Frequency Compensation Required
• Short-Circuit Protection
• Wide Common-Mode and Differential Voltage Ranges
• Low-Power Consumption
• 8-Lead TO-99 and 8-Lead PDIP
• No Latch Up When Input Common Mode Range is Exceeded