Synth & Eurorack Parts / DIY

2 to 1 heat shrink tubing variety pack. This pack includes six different diameters with four pieces of each size. Each piece is six inches in length. Features:

• Resistant to common fluids and solvents
• UL and CSA listed
• UV resistant
• Meets DEF. STAN 59.97
• Meets UL 224, 125°C and CSA C22.2 No. 198.1
• Meets MIL-DTL-23053/5 Class 2 & 3
• Flame retardant (Does not include transparent)
• Seals and protects cable splices and terminations.
• Thin wall tubing

Low cost, high quality 3.5mm patch cables in a variety of lengths and colors. The cables are super flexible, have a great droop, and are shipped coiled so no permanent kinks are formed. With the large selection of lengths and colors, these cables are the perfect choice for any sized system.

2N5457 N-Channel JFET in a TO-92 package. The 2N5457 is designed primarily for audio and switching applications.

• Max drain to gate voltage = 25 V
• Max gate to source voltage = -25 V
• Max forward gate current = 10 mA

High-quality Bourns 3362P trimpots. These single-turn cermet trimmers can be found in countless guitar pedals and synthesizer modules. Sealed trimmers are built with an o-ring seal to prevent entrance of moisture and serve as a mechanical restraint to prevent unwanted wiper movement. ±10% tolerance.

Low noise JFET quad operational amplifier. Incorporates well matched, high-voltage JFET and bipolar transistors in a monolithic integrated circuit. Features high slew rates, low input bias and offset currents, and low offset voltage temperature coefficients. Features:

• Wide common-mode and differential voltage range
• Low input bias and offset current
• Low noise en = 15 nV/HZ
• Output short-circuit protection
• High input impedance JFET input stage
• Low harmonic distortion: 0.01%
• Internal frequency compensation
• Latch up free operation
• High slew rate: 16 V/us (typical)

The 2N1711 is a silicon planar epitaxial NPN transistor in a TO-39 metal case. It is intended for use in high performance amplifiers, oscillators and switching circuits. The 2N1711 is a great choice for amplifiers where low noise is an important factor.

PT2399 echo/delay chip used in many DIY and commercial pedals. The PT2399 is in a DIP 16 package. Minimal external components are required for use and delay time is set with resistance.

High-quality USA made knobs from Davies Molding. The skirted 1900 series knobs are made of solid phenolic and feature an indicator line on the skirt. These classic knobs have been used on a variety of equipment throughout the decades and are still popularly used on synthesizers today. The smaller 1910 knob was used on many early Serge paperface panels. Davies 1910 (Small)

• Height: 0.50 in.
• Diameter: 0.75 in.
• Fits ¼" shaft with set screw

Davies 1913 (Large)

• Height: 0.625 in.
• Diameter: 1.13 in.
• Fits ¼" shaft with set screw

Anodized aluminum knob with short indicator line and set screw. This slim, solid aluminum knob has a straight knurled grip with a diameter of 0.495”. It also features a counterbore which allows it to hide pot bushings for a clean look. Fits ¼” (6.35mm) pot shafts.

Zero ohm (0Ω) resistors in a carbon film axial package. These resistors are a similar size to most common 1/4W carbon film and metal film resistors. Zero ohm resistors are useful as pcb jumpers as well as point to point jumpers. These can also be useful for true bypass 3PDT wiring.

2N6027 programmable unijunction transistor often referred to as a PUT. The 2n6027 can be found in many tremolo effects pedal projects.

LF356 single op amp in an 8-pin DIP package. The LFx5x devices are the first monolithic JFET input operational amplifiers to incorporate well-matched, high-voltage JFETs on the same chip with standard bipolar transistors (BI-FET™ Technology). These amplifiers feature low input bias and offset currents/low offset voltage and offset voltage drift, coupled with offset adjust, which does not degrade drift or common-mode rejection.

High quality 24AWG wire from Weico featuring a topcoat of solder over the strands. This wire is pre-tinned in the sense that a coating of solder is already applied, bonding the individual strands together so no additional tinning is required. This wire is ready to go as soon as it is cut and stripped making assembly that much easier. Rated at 300V and offered in a variety of colors, this wire is a great option for a variety of different projects.

CD4047B consists of a gatable astable multivibrator with logic techniques incorporated to permit positive or negative edge-triggered monostable multivibrator action with retriggering and external counting options. Inputs include +TRIGGER, -TRIGGER, ASTABLE, ASTABLE\, RETRIGGER, and EXTERNAL RESET. Buffered outputs are Q\, Q and OSCILLATOR. In all modes of operation, and external capacitor must be connected between C-Timing and RC-Common terminal, and an external resistor must be connected between the R-Timing and RC-Common terminals. Astable operation is enabled by a high level on the STABLE input or a low level on the ASTABLE\ input, or both. The period of the square wave at the Q and Q\ Outputs in this mode off operation is a function of the external components employed. "True" input pulses on the ASTABLE input or "Complement" pulses on the ASTABLE\ input allow the circuit to be used as a gatable multivibrator.

The AS3046 is Alfa’s version of the CA3046 IC in an SOIC package. The AS3046D consists of five general purpose silicon NPN transistors on a common monolithic substrate. Two of the transistors are internally connected to form a differentially-connected pair. The transistors are well suited to a wide variety of applications in low power systems. They may be used as discrete transistors in conventional circuits however, in addition, they provide the very significant inherent integrated circuit advantages of close electrical and thermal matching. The AS3046D is available in a 14-pin SOIC package. Features

• Matched pair of npn transistors
• VBE matched less than ±1 mV
• 5 general purpose monolithic transistors
• Wide operating current range

Applications

• Filters
• Custom designed differential amplifiers
• Temperature compensated amplifiers

For N364 and X5, 5 are required. for N264, 2 are needed. May be cut. Sold individually. These are also used in the Kurzweil MK (MARK)-Series of electronic pianos.

High-quality USA made knobs from Rogan Corp. These large, skirted pointer knobs from Rogan’s PT Series feature a soft rubber grip molded over a solid polymer knob. PT Series knobs can be found on synthesizer modules from Make Noise, Mutable Instruments and others. Fits 6mm D-shafts.

• Height: 0.71 in
• Diameter: 0.73 in
• Fits 6mm D Shafts
• Indicator on round side of D-shaft

A variety of different sizes are available from the PT Series.

Genuine Carling 2 Position Mini Toggle, On-On, Short Round Bat, Right Angle, PC Mount Features:

• SPDT ( Single Pole/ Double Throw) On-On switch
• 0.275" bushing length
• 0.270” bat length
• ¼" chassis hole diameter
• Right angle, PC Mount terminals

Note: On-On switches may sometimes be referred to as On-None-On.

Reverse audio taper Alpha 16mm pots with a solid shaft and right angle PCB mount terminals. The smaller size is useful for builds with limited panel space such as guitar pedals, synthesizer modules, and adding modifications to equipment. Washer and nut included.

• Threading: M7 x 0.75
• Distance between terminals: 5 mm (0.197”)
• Lead Depth from Panel: 10.7 mm + 5 mm (0.421” + 0.197”)
• Lead Distance from shaft center: 16 mm (0.630”)
• Lead Thickness: 0.5 mm (0.020”)
• Shaft Diameter: 6.35 mm (0.25”)

Replacement nut and washer for pots and jacks that feature a ⅜" bushing with 3/8-32 threading. Sold in packs containing 100 nuts and 100 washers.

OP07 precision op amp in an 8-pin DIP package.These devices offer low offset and long-term stability by means of a low-noise, chopperless, bipolar-input-transistor amplifier circuit. For most applications, external components are not required for offset nulling and frequency compensation. The true differential input, with a wide input-voltage range and outstanding common-mode rejection, provides maximum flexibility and performance in high-noise environments and in noninverting applications. Low bias currents and extremely high input impedance are maintained over the entire temperature range.

Linear taper, vertical mount, Alpha pots with a 6.35mm shaft diameter and a center notch (detent). The center notch is useful for builds where the center position of the pot is commonly used such as panners or EQ controls. These 9mm pots are popular in DIY guitar pedals, synthesizers, and other projects. Mounting nut and washer included.

NJM4580L dual op amp from JRC in a SIP8 package. The NJM4580L is the same as the DIP NJM4580 (JRC4580) otherwise. The SIP version is a great replacement for dual op amps in vintage circuits as well as a space saving package for some PCB layouts. The NJM4580 is a dual operational amplifier, specially designed for improving the tone control, which is most suitable for the audio application. Featuring noiseless, higher gain bandwidth, high output current and low distortion ratio, and it is most suitable not only for acoustic electronic parts of audio pre-amp and active filter, but also for the industrial measurement tools.

Lens Diameter: 3 mm Overall Height: 5.4 mm Lens Type: Diffused Multiple color options available.