Synth & Eurorack Parts / DIY

The AS3310 is Alfa’s version of the CEM3310 IC. The AS3310 is a self-contained, precision ADSR type of envelope generator intended for electronic music and other sound generation applications. Attack, decay and release times are exponentially voltage controllable over a wide range, and the sustain level is linearly voltage controllable from 0 to 100% of the peak voltage Vp. All four control Inputs are Isolated from the rest of the circuitry so that the control pins of tracking units may be simply tied together.
On the negative power output, there is an internal Zener diode at 7.4 volts ± 10%, which allows the chip to supply a maximum voltage of ± 15 volts with a current-limiting resistor REE, and a minimum positive supply voltage of + 11 volts and a minimum negative supply voltage of -5 volts.. A series current limiting resistor must be added between pin 6 and the supply.

New-old-stock Soviet pilot lights that fit screw base bulbs. These lights have a unique bakelite frame and bakelite bezel. The lights come with a 6.3V bulb but can be used with any G-3-½ screw base bulb. The diameter of the light is 0.785” and the diameter of the mounting hole is 0.625”. Includes a bakelite mounting nut. Note: A small 0.2” notch must either be filed into the 0.625” mounting hole or filed off of the light to flush mount with a panel.

PCB for converting SMD SSOP-16 packages to through hole DIP-16 footprints. Solder the device to this PCB then attach pin headers (sold seperately) to connect to through hole footprints on PCBs, breadboards and IC sockets.

The BC337 is a silicon general purpose NPN transistor in a TO-92 package. The BC337’s typical applications include signal processing, amplification, and switching. The BC337 is available in three different gain ranges: BC337-16, BC337-25, and BC337-40. Type hFE Range (IC=100mA, VCE=1V) Typical hFE (IC=100mA, VCE=1V) BC337-16 100-250 160 BC337-25 160-400 250 BC337-40 250-630 400

The CD40106B device consists of six Schmitt-Trigger inputs. Each circuit functions as an inverter with Schmitt-Trigger input. The trigger switches at different points for positive- and negative-going signals. The difference between the positive-going voltage (VP) and the negative-going voltages (VN) is defined as hysteresis voltage (VH). Features:

• Schmitt-Trigger Inputs
• Hysteresis Voltage (Typical):
  
  • 0.9 V at VDD = 5 V
  • 2.3 V at VDD = 10 V
  • 3.5 V at VDD = 15 V
• Noise Immunity Greater Than 50%
• No Limit On Input Rise and Fall Times
• Standardized, Symmetrical Output Characteristics
• For Quiescent Current at 20 V
• Maximum Input Current Of 1 µA at 18 V Over Full Package Temperature Range: 100 nA at 18 V and 25°C
• Low VDD and VSS Current During Slow Input Ramp
• 5-V, 10-V, and 15-V Parametric Ratings

CD4046B CMOS Micropower Phase-Locked Loop (PLL) consists of a low-power, linear voltage-controlled oscillator (VCO) and two different phase comparators having a common signal-input amplifier and a common comparator input. A 5.2-V zener diode is provided for supply regulation if necessary. Features:

• Very low power consumption: 70 µW (typ.) at VCO fo = 10 kHz, VDD = 5 V
• Operating frequency range up to 1.4 MHz (typ.) at VDD = 10 V, RI = 5 k
• Low frequency drift: 0.04%/°C (typ.) at VDD = 10 V
• Choice of two phase comparators:
  
  • Exclusive-OR network (I)
  • Edge-controlled memory network with phase-pulse output for lock indication (II)
• High VCO linearity: <1% (typ.) at VDD = 10 V
• VCO inhibit control for ON-OFF keying and ultra-low standby power consumption
• Source-follower output of VCO control input (Demod.

High quality nylon M3 flat washers. These durable washers fit perfectly on M3 threaded screws. The small outside diameter provides a clean look beneath the head of the screw. These are great mounting washers for preventing rack rash on front panels like Eurorack synths or any other use where the surface beneath the screw requires protection.

Small PCB adapter boards to convert PCB mount 9mm vertical pots to wired panel mount pots. These adapters are great for tight builds allowing for more densely populated panels than 16mm options. They’re also a great way to incorporate sealed potentiometers into builds where larger sized options would be cost prohibitive.

Black stripboard featuring a 0.15” vintage spacing. This spacing is great for vintage-style builds and more easily accommodates axial capacitors and other larger sized vintage parts like resistors and transistors. The board has 40 x 20 holes (20 strips). Each strip is HASL coated making soldering easier than most protoboards and also ensures a long shelf life. Features:

• High-quality 1.6mm FR4 glass-epoxy circuit board
• HASL coated strips
• 40 x 20 holes (20 strips)
• 6.14” x 3.15”

Looking for projects? See our Wide Stripboard projects in our Pedal Layouts & Build Guides section for ideas.

2N6027 programmable unijunction transistor often referred to as a PUT. The 2n6027 can be found in many tremolo effects pedal projects.

LF356 single op amp in an 8-pin DIP package. The LFx5x devices are the first monolithic JFET input operational amplifiers to incorporate well-matched, high-voltage JFETs on the same chip with standard bipolar transistors (BI-FET™ Technology). These amplifiers feature low input bias and offset currents/low offset voltage and offset voltage drift, coupled with offset adjust, which does not degrade drift or common-mode rejection.

High-quality USA made knobs from Rogan Corp. These medium pointer knobs from Rogan’s PT Series feature a soft rubber grip molded over a solid polymer knob. PT Series knobs can be found on synthesizer modules from Make Noise, Mutable Instruments and others. Fits 6mm T18 knurled shafts.

• Height: 0.68 in.
• Diameter: 0.50 in.
• Fits T18 Knurled Shafts

For a D-shaft version of this knob, see P-K282P-W. A variety of different sizes are available from the PT Series. See the links below for the full selection of knurled shaft knobs from this series. P-K271P-W 1P Small Pointer P-K271PS-W 1PS Small Skirted Pointer P-K272PS-W 2PS Medium Skirted Pointer

OP275 dual audio op amp in an 8-pin DIP package. The OP275 is the first amplifier to feature the Butler Amplifier front end. This new front end design combines both bipolar and JFET transistors to attain amplifiers with the accuracy and low noise performance of bipolar transistors, and the speed and sound quality of JFETs. Total Harmonic Distortion plus Noise equals that of previous audio amplifiers, but at much lower supply currents. A very low l/f corner of below 6 Hz maintains a flat noise density response. Whether noise is measured at either 30 Hz or 1 kHz, it is only 6 nVHz. The JFET portion of the input stage gives the OP275 its high slew rates to keep distortion low, even when large output swings are required, and the 22 V/µs slew rate of the OP275 is the fastest of any standard audio amplifier.

Audio taper, vertical mount, dual gang Alpha pots with a 6.35mm shaft diameter. Dual gang pots are useful for stereo controls and other circuits requiring two separate pots moving in tandem. These 9mm pots are popular in DIY guitar pedals, synthesizers, and other projects. Mounting nut and washer included. See R-VAV-BX-DUAL for linear taper versions.

High-quality USA made knobs from Davies Molding. The 8000 series knobs are made of solid phenolic and feature a classic teardrop design. The detailed design makes these knobs a striking addition to any piece of equipment. This unique design has been used on a variety of tools and instruments. Davies 8005 (Small)

• Height: 0.78 in.
• Length: 1.05 in.
• Fits ¼" shaft with set screw

Davies 8010 (Large)

• Height: 1 in.
• Length: 1.25 in.
• Fits ¼" shaft with set screw

High-quality USA made knobs from Rogan Corp. These medium, skirted pointer knobs from Rogan’s PT Series feature a soft rubber grip molded over a solid polymer knob. PT Series knobs can be found on synthesizer modules from Make Noise, Mutable Instruments and others. Fits 6mm T18 knurled shafts.

• Height: 0.84 in.
• Diameter: 0.62 in.
• Fits T18 Knurled Shafts

For a D-shaft version of this knob, see P-K282PS-W. A variety of different sizes are available from the PT Series. See the links below for the full selection of knurled shaft knobs from this series. P-K271P-W 1P Small Pointer P-K271PS-W 1PS Small Skirted Pointer P-K272P-W 2P Medium Pointer

This small PCB is a simple way to add an indicator light that pulses to the rate of LFOs and clocks used in pedals, synthesizers, and other equipment. Simply connect the positive supply voltage to V+, ground to GND, and the output of a positive signal (0 to V+) such as an LFO or clock to the IN pad. The trimmer can adjust how the LED reacts to the signal. Fully clockwise it will simply pulse on and off when paired with a strong signal. If the signal is a sine, triangle, or any other non-pulse type signal, adjusting the trimmer counter clockwise can dial in settings that follow the shape of the waveform, brightening and dimming with the changing voltage. For certain dual op-amp LFOs in effect pedals, the signal may not go low enough to turn the LED fully off.

Dual wide-bandwidth LF353 opamps in an 8-pin DIP package. The LF353 offers a high input impedance and 3MHz bandwidth.
This LF353 device is a low-cost, high-speed, JFET input operational amplifier with very low input offset voltage. It requires low supply current yet maintains a large gain-bandwidth product and a fast slew rate. In addition, the matched high-voltage JFET input provides very low input bias and offset currents.

µA741 single op amp in an 8-pin DIP package. The µA741 device is a general-purpose operational amplifier featuring offset-voltage null capability. The high common-mode input voltage range and the absence of latch-up make the amplifier ideal for voltage-follower applications. The device is short-circuit protected and the internal frequency compensation ensures stability without external components. A low-value potentiometer may be connected between the offset null inputs to null out the offset voltage. Features

• Short-Circuit Protection
• Offset-Voltage Null Capability
• Large Common-Mode and Differential Voltage Ranges
• No Frequency Compensation Required
• No Latch-Up

Prototyping circuit board (PCB) designed to fit the Hammond 1590B die-cast aluminum enclosure. It has a convenient 2-hole pattern, which provides an easy way to connect parts while maximizing usable board area. It can be used as a stand-alone prototyping board, or installed in a Hammond 1590B enclosure. For fastening your project to a surface see our adhesive standoffs (S-H190) Features:

• Single-sided high-quality FR4 glass-epoxy circuit board.
• Convenient 2-hole pattern provides an easy way to connect parts.
• 1oz/ft2 copper with an anti-tarnish coating for easy soldering. Lead free and RoHS compatible.
• 0.042" holes are drilled on 0.1" (2.54mm) centers. 2 mounting holes.
• PCB Size 2.05 x 4.05 in (52.1 x 102.9 mm)

2SC945 NPN transistors. This is a silicon NPN transistor in a TO-92 package. The 2SC945 was used in many classic Boss pedals such as the CE-2 chorus.

The BC548 is a silicon general purpose NPN transistor in a TO-92 package. The BC548’s typical applications include signal processing, amplification, and switching. The BC548 is available in two different gain ranges: BC548B and BC548C. Type hFE (IC=2mA, VCE=5V) BC548B 200-450 BC548C 420-800

2 to 1 heat shrink tubing variety pack. This pack includes six different diameters ranging from 1/16” to 1/2”. Each piece is 2.5” in length. This set comes in a hard plastic case perfect for sorting and storing heat shrink. Features:

• Resistant to common fluids and solvents
• UL and CSA listed
• UV resistant
• Meets DEF. STAN 59.97
• Meets UL 224, 125°C and CSA C22.2 No. 198.1
• Meets MIL-DTL-23053/5 Class 2 & 3
• Flame retardant (Does not include transparent)
• Seals and protects cable splices and terminations.
• Thin wall tubing

ST2 StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. ST2 has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features

• Standard stripboard pattern, with tracks running the length of the board.
• Single-sided high-quality FR4 glass-epoxy circuit board.
• 1oz/ft2 copper with an anti-tarnish coating for easy soldering.