You are here

Synth & Eurorack Parts / DIY

Our Synth & Eurorack Parts / DIY category is a curated list of items that are commonly found in synth/eurorack projects. The items and filters here do not represent our full lineup of parts. If you don't see what you are looking for, check out our main categories or send us a suggestion and we'll look into adding it.

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(16 pages)
P-PC-SB400Breadboard - Solderable PCB, 3.00” x 1.90”

The SB400 Solderable PCB BreadBoard enables you to transfer your circuit and wires from a plug-in breadboard without recutting wires or changing your layout. The SB400 has the same pattern and spacing as a standard 400 connection point BB400 solderless plug-in breadboard. It has a standard 5-hole strip for each IC pin, just like solderless breadboards plus 4 power rails. However, it has the advantage that soldered joints provide a more reliable long-term connection than solderless contacts. The SB400 has four power rails like solderless breadboards, plus two bonus rails for power or signals. There are bonus two-hole pads along the centerline allowing DIL (dual in-line) headers to be used. BPS prototyping boards use high-quality FR4 glass epoxy PCBs for long life, with an anti-tarnish protective coating for easy soldering.


$4.95
Click to read more
P-PC-ST2StripBoard - Single Sided, 3.94” x 3.15”, Mounting Holes

ST2 StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. ST2 has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features



  • Standard stripboard pattern, with tracks running the length of the board.
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.

$5.50
Click to read more
P-PC-PAD2PadBoard - Double Sided, Plated Holes, 3.94” x 3.15”, Mounting Holes

The PadBoard-2 prototyping circuit board has a general purpose pad-per-hole pattern which is good for analog and digital use. It is a double-sided board with plated holes, which allows components to be soldered to either side of the board. A square pad is provided every 5th hole, which makes it easy to align components on the top and bottom of the board. Features



  • Pad-per-hole prototyping board with plated-thru holes. A square pad every 5th hole makes it easy to align components on top and bottom.
  • Double-sided high-quality FR4 glass-epoxy circuit board with plated holes. Components can be soldered to either side.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering. Lead free and RoHS compatible.
  • 31 x 39 holes, 0.037" holes are drilled on 0.1" (2.54mm) centers. Four 0.125” mounting holes.
  • Size2 = 100 x 80mm (3.94 x 3.15in), 1/16" thick (1.6mm)

$6.85
Click to read more
P-PC-ST3UStripBoard - Single Sided, 6.30” x 3.94”

ST3U StripBoard is a prototyping circuit board with a standard long strip pattern. Tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads. It has 0.1" hole spacing for DIP integrated circuits and headers and other parts. It has higher quality than traditional stripboard. The holes are drilled, not punched. The base material is high-quality FR4 glass epoxy board. It has better stability and moisture resistance than boards using phenolic or SRBP (synthetic resin bonded paper), which can warp with exposure to humidity. Features



  • Standard stripboard pattern, with tracks running the length of the board.
  • Single-sided high-quality FR4 glass-epoxy circuit board.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.

$9.95
Click to read more
P-PC-PAD3UPadBoard - Double Sided, Plated Holes, 6.30” x 3.94”, Mounting Holes

The PadBoard-3U prototyping circuit board has a general purpose pad-per-hole pattern which is good for general purpose analog and digital use. It is a double-sided board with plated holes, which allows components to be soldered to either side of the board. A square pad is provided every 5th hole, which makes it easy to align components on the top and bottom of the board. The PCB accepts a 96 pin DIN-41612 VME connector for backplane or board-to-board applications. Holes for ejector latches are provided. Features



  • Pad-per-hole prototyping board with plated-thru holes. A square pad every 5th hole makes it easy to align components on top and bottom.
  • Double-sided high-quality FR4 glass-epoxy circuit board with plated holes. Components can be soldered to either side.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.

$12.95
Click to read more
P-H5419Switch - Carling, Mini Toggle, DPDT, 2 Position, Solder Lugs, Flatted

Carling mini-toggle switch, DPDT, ideal for phase switching, coil-tapping, series/parallel pickup switching in guitars. This switch features a flattened actuator.



  • 0.354" bushing length
  • ¼" mounting hole diameter
  • Double pole/Double throw (DPDT)

$4.95
Click to read more
P-K800XKnob - Mini Indicator, Set Screw, 15mm x 11mm
Colors Available:
New!:

Knob with line and set screw, 15mm x 11mm.


$0.75
Click to read more
P-K900XKnob - Chicken Head, mini, high-quality, brass insert, Set Screw
Colors Available:
New!:

High quality miniature chicken head knob with set screw for smaller applications. 0.90" long nose to tail. Mini Davies 2300 clone.


$0.79
Click to read more
P-K380XKnob - Small, Indicator Line, set screw
Colors Available:
New!:

Small knobs, .744" diameter, .57" height. Davies 1510 clone.


Starting at $0.70
Click to read more
R-VSHL-AXPotentiometer - Song Huei, Audio, 9mm, Tall

Audio taper, vertical mount, Song Huei pots with a 6mm shaft. These 9mm pots are popular in DIY guitar pedals, modular synthesizers, and other projects where space is limited. The knurled shaft features a painted indicator line so no knob is required. These tall versions have a 17mm shaft length and a total height of 25mm. For linear taper versions, see R-VSHL-BX. For center notched, linear taper versions, see R-VSHL-BX-CN.


$0.80
Click to read more

Pages

(16 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Synth & Eurorack Parts / DIY