Terminal Boards & Strips

Supa Fuzz style circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the SupaFuzz pedal. The board is styled after the first version that Marshall produced which featured a printed circuit rather than a stripboard construction. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.

230 x 70 mm, loaded with 33 turrets,2 mm board thickness. This is designed for a 5E3 board.

Phenolic PCBs with similar styling to the eyelet/fiberboard used in vintage equipment. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. The spacing between pads is 7.5mm horizontally and 26mm vertically. The two mounting holes have a 3.2mm diameter to fit M3 or 4-40 hardware and also fit the S-H190 adhesive standoffs perfectly. See P-HTB-X for black version. See P-HTB-PG-X for premium black version. 2x8 Board:

• 2 rows of 8 eyelets (16 total)
• 7.5mm x 26mm eyelet spacing
• 57.15mm x 30.66mm board
• 45mm spacing for 3.2mm mounting holes
• Great fit for 125B and 1590N1 enclosures

2x12 Board:

• 2 rows of 12 eyelets (24 total)
• 7.5mm x 26mm eyelet spacing
• 87.15mm x 30.66mm board
• 75mm spacing for 3.2mm mounting holes
• Great fit for 1590BB enclosures

Our 3PDT PCB daughterboard is a small board designed to simplify the wiring of 3PDT footswitches in guitar pedals. All inputs and outputs are clearly labeled on the PCB, removing any confusion about how the footswitch should be wired, and decreasing the chances of wiring mistakes or short-circuits.

Standard size terminal strip, 1/16" thick bakelite, tin plated steel lugs and brackets on 3/8" centers.

PCBs with similar styling to the eyelet/fiberboard used in vintage equipment. The spacing between pads is 7.5mm horizontally and 26mm vertically.

Turrets for use on boards measuring 3mm thick, such as P-HTUR-189-3BK or P-HTUR-189-3R. For 2mm boards, see S-HTUR-SG-2X
Stake and anvil required for mounting.

• Staking Tool is our part number: S-T1715
• Anvil is our part number S-T1717
• For a budget tool set see S-T-STAKE-SET

HS Treble Booster style circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the Hornby Skewes ‘Treble Booster’ pedal. The board is styled after a version of the silicon Treble Booster but can be used for the germanium version as well. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. This board includes a blank mounting PCB. This PCB sits directly beneath the main board to mount it directly to the enclosure using a screw. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.

300mm x 60mm turret board conveniently pre-loaded with 2 rows of 30 turrets. Save yourself some time loading the board and move on to building your project!

• Accepts 2mm turrets.

Bifurcated turrets for use on boards measuring 2mm thick. Made of nickel plated copper. These are sometimes referred to as split or forked turrets. For use with 3mm boards, see S-HTUR-BI-3S. Stake and anvil required for mounting. Staking Tool is our part number S-T1715. Anvil is our part number S-T1717. For a budget tool set see S-T-STAKE-SET.

Staking tool for small eyelets such as S-HEYE-B. Directions:

• Drill hole using #42 drill bit
• Insert eyelet
• Flip board over onto a hard service
• Center staking tool over the eyelet
• Strike staking tool with hammer to clamp eyelet to board

Standard size terminal strips, 1/16" thick bakelite, tin plated steel solder lugs and brackets on 3/8" centers.

Two rows of 15 U-style terminals (30 total) on a black board. The U-style terminal strips are spaced 8.3mm apart allowing for more densely populated point-to-point builds. The boards are 0.063” thick.

Marshall PC Board for TSL 100 / 122. Rev 20.

Zonk II style circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the Zonk II pedal. The board is styled after the version that featured silicon transistors and a printed circuit rather than a stripboard construction. It is actually a cut down version of the Shatterbox PCB using only the fuzz side of that pedal. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. The copper traces have a surface treatment providing protection from corrosion. This board includes a blank mounting PCB. This PCB sits directly beneath the main board to mount it directly to the enclosure using screws. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.

Blank board, 10-1/8" x 2-5/8", 189 3mm holes on 3/8" centers.

• Blue, Green, Yellow: 2 mm board thickness
• Black, Red: 3 mm board thickness

For vintage style phenolic boards, see P-HTUR-189-BRN and P-HTUR-216-BRN.

Bifurcated turrets with a screw mount that works on boards with thicknesses of 1.5mm to 4mm. Made of gold plated brass. These are sometimes referred to as split or forked turrets. Includes a mounting washer, lock washer, and mounting nut. The staking tool is not required for these turrets.

Staking tool set that includes both the anvil and swage/punch. The set works with standard turret and eyelet sizes commonly used in amplifiers. The anvil also can be used with Y style turrets.

Standard size terminal strips, 1/16" thick bakelite, tin plated steel solder lugs and brackets.

3PDT switch mounted charge pump PCB for positive ground effects. This small PCB simplifies the wiring of 3PDT foot switches in guitar pedals while also offering -9V when used with a standard +9V power supply. This is a great option for positive ground effects such as vintage fuzz pedals. The circuit of this PCB also features a protection diode and an LED indicator for when the effect is engaged.
This board is compatible with the MAX1044, TC1044S, TC7660S, and LT1054 charge pump ICs.

Turret strip, with 6 turrets. Measures 67mm x 15.875mm.

High quality bifurcated (slotted) turrets with a hollow post. These terminals are made of annealed brass with a 100% tin over nickel plating. These slotted turrets closely resemble those found in vintage Marshall amps.

• Triple turret with slot
• 9.12mm height when installed
• 3.18mm diameter
• For 3.0mm to 3.2mm panel thickness
• Recommended for mounting holes sized 2.68mm to 2.78mm
• Bright 100% tin finish
• Knurled underside of shoulder to prevent rotation once swaged

Stake and anvil required for mounting.

• Staking Tool is our part number: S-T1715
• Anvil is our part number S-T1717
• For a budget tool set see S-T-STAKE-SET

Turret strip, with 23 turrets. Measures 241.3mm x 15.875mm.

Mini size terminal strips, 1/16" thick phenolic, tin plated brass solder lugs and brackets on 1/4" centers.