Terminal Boards & Strips

Board - Marshall, Replacement for JCM 2000 DSL 100
Replacement board for Marshall JCM 2000 DSL 100 amplifiers which frequently have issues with original boards. This replacement can bring your amp back to life!
$209.95
Out of Stock
Connector - Uninsulated Fork Terminal, #8
Uninsulated fork terminals for use with #8 studs. These terminals fit 22AWG through 16AWG wire gauges and feature a serrated barrel for a strong crimped connection. Made of tin plated copper.
$2.50
package of 10
Contact Pin - Nickel Plated Brass, Seamless, 0.566" Height
0.125" diameter nickel plated brass contact pin. Fits .062" and .093" boards. Height is .566" when mounted. In addition to turret board use, these pin connectors are often found on printed circuit boards. They are referred to as through hole terminal pins, header pins, or crimp contact pins.
$0.15
Eyelets - Brass, .121 x .125 x .200; MT .0095, package of 10
Eyelets, bag of 10 (mounts in 1/8" hole).
$0.80
package of 10
Eyelets - Plated Brass, Small, .089” x .125” x .150”
Tin plated brass eyelets commonly used on vintage style pickups. The small sized eyelets are also great for smaller point-to-point projects such as DIY stomp boxes. The outside diameter of the barrel is 0.089” and the recommended mounting hole is 0.093” using a #42 drill bit.
$0.85
package of 10
Fiberboard - Vulcanized, 3" x 15", .062" Thick
Vulcanized Fiberboard, used for laying out circuits using eyelets such as S-HEYE-A and our staking tool S-T1715.
  • .062" thick
  • 3" x 15"
$2.65
Kit - Fender® Stratocaster® Mid Boost Kit
Genuine Fender® Mid Boost upgrade kit for Strats with active electronics. This circuit is used in the signature Eric Clapton and Buddy Guy strats and is commonly referred to as the Clapton Boost. The Mid Boost knob adjusts gain from 0 dB (no boost) to 25 dB (maximum boosted mids). This boost sounds great clean and adds powerful control to distortion.
$59.95
Padboard - Single-Sided, 6.14” x 3.15”, Modern Spacing, Phenolic Board
Perfboard / padboard made with a phenolic substrate. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This perfboard features a 0.1” modern spacing. The board has 60 x 30 holes with squared copper pads on one side of the board. The copper is surface-treated, making soldering easier than most protoboards and also ensuring a long shelf life.
$6.75
PC Board - Dunlop, replacement for Crybaby
Original Crybaby replacement circuit board for pedals made after 1990. Original Dunlop replacement part.
$29.45
PCB - Charge Pump, -9V from +9V, 3PDT Switch Mount
3PDT switch mounted charge pump PCB for positive ground effects. This small PCB simplifies the wiring of 3PDT foot switches in guitar pedals while also offering -9V when used with a standard +9V power supply. This is a great option for positive ground effects such as vintage fuzz pedals. The circuit of this PCB also features a protection diode and an LED indicator for when the effect is engaged.
This board is compatible with the MAX1044, TC1044S, TC7660S, and LT1054 charge pump ICs.
$1.60
PCB - Charge Pump, -9V from +9V, Screw Mount
Screw mounted charge pump PCB for positive ground effects. This small PCB provides -9V when used with a standard +9V power supply. This is a great option for positive ground effects such as vintage fuzz pedals. The PCB has a low profile design and is a simple addition to any build using a standoff to mount the board. This board is compatible with the MAX1044, TC1044S, TC7660S, and LT1054 charge pump ICs.
$1.95
PCB - Daughterboard for Wiring 3PDT Footswitches
Our 3PDT PCB daughterboard is a small board designed to simplify the wiring of 3PDT footswitches in guitar pedals. All inputs and outputs are clearly labeled on the PCB, removing any confusion about how the footswitch should be wired, and decreasing the chances of wiring mistakes or short-circuits.
$0.95
PCB - Marshall, Valve PCB TSL100 / TSL122, Rev 20
Marshall PC Board for TSL 100 / 122. Rev 20.
$209.95
Out of Stock
PCB - Mod® Electronics, Germanium Fuzz, For 1590B or 1590N1
PCB for a Fuzz Face style circuit with PCB mounted potentiometers. Its very low component count makes it a great beginner project. Builders can use preselected transistors from P-Q2N1309-SET-FF with its included resistors for R1 through R4 for a simple and great sounding germanium fuzz. If a builder wants to use their own transistors, the stock component values are also clearly labeled on the PCB. The transistor footprints fit P-SGP-001 sockets making swapping transistors a simple process so builders can experiment with a variety of types and values. This board was designed for a 1590N1/125B or C65-sized enclosure, with the potentiometers spaced 30mm apart. It can also be mounted using the two screw-mount holes with the potentiometers wired off-board. There are two screw-mounting holes which are designed for M3 screws.
$3.50
PCB - Premium Pseudo Eyelet Board, 7.5mm Spacing
Premium versions of the pseudo eyelet boards with 7.5mm spacing. The premium versions feature 2.4mm thick boards with gold plated contacts. These PCBs have similar styling to the eyelet/fiberboard used in vintage equipment. The spacing between pads is 7.5mm horizontally and 26mm vertically. The two mounting holes have a 3.2mm diameter to fit M3 or 4-40 hardware and also fit the S-H190 adhesive standoffs perfectly. For standard versions, see P-HTB-X. 2x8 Board:
  • 2 rows of 8 eyelets (16 total)
  • 7.5mm x 26mm eyelet spacing
  • 57.15mm x 30.66mm board
  • 45mm spacing for 3.2mm mounting holes
  • Great fit for 125B and 1590N1 enclosures

2x12 Board:
  • 2 rows of 12 eyelets (24 total)
  • 7.5mm x 26mm eyelet spacing
  • 87.15mm x 30.66mm board
  • 75mm spacing for 3.2mm mounting holes
  • Great fit for 1590BB enclosures
$3.25
PCB - Pseudo Eyelet Board, 2X8, 9.1mm Spacing, Phenolic Board
Phenolic PCBs with similar styling to the eyelet/fiberboard used in vintage equipment. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. The spacing between pads is 9.1mm horizontally and 34.4mm vertically. The two mounting holes have a 3.2mm diameter to fit M3 or 4-40 hardware and also fit the S-H190 adhesive standoffs perfectly. See P-HTB-X for 7.5mm spacing 2x8 Board:
  • 2 rows of 8 eyelets (16 total)
  • 9.1mm x 34.4mm eyelet spacing
  • 69.42mm x 40.1mm board
  • 54.6mm spacing for 3.2mm mounting holes
  • Great fit for 1590P1, Gorva S90, and YY slanted enclosures
$2.15
PCB - Pseudo Eyelet Board, 6.35mm Spacing, 2 x 9
PCBs with similar styling to the eyelet/fiberboard used in vintage equipment. The spacing between pads is 6.35mm horizontally and 22mm vertically. The two mounting holes have a 3.2mm diameter to fit M3 or 4-40 hardware and also fit the S-H190 adhesive standoffs perfectly. 2x9 Board:
  • 2 rows of 9 eyelets (18 total)
  • 6.35mm x 22mm eyelet spacing
  • 55.44mm x 26.66mm board
  • 45mm spacing for 3.2mm mounting holes
  • Great fit for 1590B and Gorva C65 enclosures
$1.60
PCB - Pseudo Eyelet Board, 7.5mm Spacing
PCBs with similar styling to the eyelet/fiberboard used in vintage equipment. The spacing between pads is 7.5mm horizontally and 26mm vertically.
Starting at $1.50
PCB - Pseudo Eyelet Board, 7.5mm Spacing, Phenolic Board
Phenolic PCBs with similar styling to the eyelet/fiberboard used in vintage equipment. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. The spacing between pads is 7.5mm horizontally and 26mm vertically. The two mounting holes have a 3.2mm diameter to fit M3 or 4-40 hardware and also fit the S-H190 adhesive standoffs perfectly. See P-HTB-X for black version. See P-HTB-PG-X for premium black version. 2x8 Board:
  • 2 rows of 8 eyelets (16 total)
  • 7.5mm x 26mm eyelet spacing
  • 57.15mm x 30.66mm board
  • 45mm spacing for 3.2mm mounting holes
  • Great fit for 125B and 1590N1 enclosures

2x12 Board:
  • 2 rows of 12 eyelets (24 total)
  • 7.5mm x 26mm eyelet spacing
  • 87.15mm x 30.66mm board
  • 75mm spacing for 3.2mm mounting holes
  • Great fit for 1590BB enclosures
Starting at $1.85
PCB - Pseudo Eyelet Board, 9.1mm Spacing
PCBs with similar styling to the eyelet/fiberboard used in vintage equipment. The spacing between pads is 9.1mm horizontally and 34.4mm vertically. The two mounting holes have a 3.2mm diameter to fit M3 or 4-40 hardware and also fit the S-H190 adhesive standoffs perfectly. See P-HTB-X for 7.5mm spacing 2x8 Board:
  • 2 rows of 8 eyelets (16 total)
  • 9.1mm x 34.4mm eyelet spacing
  • 69.42mm x 40.1mm board
  • 54.6mm spacing for 3.2mm mounting holes
  • Great fit for 1590P1, Gorva S90, and YY slanted enclosures

2x10 Board:
  • 2 rows of 10 eyelets (20 total)
  • 9.1mm x 34.4mm eyelet spacing
  • 87.1mm x 40.1mm board
  • 72.8mm spacing for 3.2mm mounting holes
  • Great fit for 1590BB enclosures
Starting at $2.45
PCB - Pseudo Eyelet Board, ½” Spacing, Generic AB763, 3 x 29
Pseudo eyelet boards with 3 rows of ½” spacing. These 2mm thick boards have a vertical spacing of 1” from row to row. The pseudo eyelet PCBs have similar styling to the eyelet/fiberboard used in vintage equipment. The size and layout of the 3 x 29 works well for AB763 style builds. For a blank board to pair with this one for use as an insulator, see P-HBB-3X29.
  • 3 rows of 29 eyelets (87 total)
  • 0.5” x 1” eyelet spacing
  • 14.5” x 2.5” board
  • Great fit for AB763 style builds
$10.95
PCB - Triangle Big Muff, Diagonal Perfboard, Phenolic Board
Triangle Big Muff style circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the distinct diagonal-pattern perfboard used in the earliest Triangle Big Muff units. This style of board was sold as a general-purpose prototyping board in that era, and can accommodate a variety of vintage-style builds.
$3.95
PCB - Vintage Style Circuit board, CMOS Fuzz, Phenolic Board
This board is for a CMOS fuzz topology popularized by Craig Anderton’s Tube Sound Fuzz from the mid-70s. The board uses a new design with old-school traces on phenolic substrate for an era-appropriate look. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. The circuit is based around a CD4049 CMOS hex inverter and was also the basis for other fuzz designs, including the Way Huge Red Llama. The board fits in a 1590BB and works well with our pre-drilled layout P-H1590BBBK-PD2. A layout can be found in our Documents section below. Recommended parts using Vishay PR02 resistors can be found in the below table.
$3.65
PCB - Vintage Style Circuit Board, Eyelet-Rite Fuzz, Phenolic Board
Eyelet-Rite fuzz circuit board made with a phenolic substrate for an even closer match to the vintage production boards. Phenolic boards are found in many vintage electronics before the use of fiberglass became common. This board is a recreation of the circuit board found in the germanium Mosrite Fuzzrite pedals. The board is styled after the point to point version that used eyelets. When drawing the layout, original boards were closely referenced to ensure a proper match and fit. This board is intended for use with S-HEYE-A eyelets and is directly mounted to a Carling P-H550 footswitch (both sold separately). The original build also used a unique C350K pot and the R-VOMSL-350KRA is the perfect substitute. The build style is very straightforward with point to point connections. For a detailed drawing of the parts and connections originally used on this board, please see the layout drawing linked below.
$3.55