Test Lead - Set, Military Specification

Item Unavailable

Sorry! You are trying to check out one of our items which is no longer available. Why not check out one of these alternate options?

Jumper Test Lead Set - Clip 35mm, Total Length 24", 22AWG
Set of 10 Jumper Test Leads " Alligator Clips 35mm each. Total Length 24", 22AWG wire. Black, Red, White, Yellow, Green
$4.99
package of 10
Bias Master™ - TAD, tube tester, with 4 probes
Bias Master™ system BM4 Measures Bias current of the vacuum tubes in your amp. Includes 4 probes and english/german operation manual. The Bias Master™ allows you to monitor the bias current safely and easily. While adjusting the Bias control pot of your amp, the Bias Master™ shows the actual result. This lets you set and evaluate the full reasonable biasing range your amp and tubes offer to find and set your personal perfect choice.
$228.95
Transistor Set - tested and selected for Fuzz Face, 2N1309, PNP, Germanium
This is a set of two 2N1309 germanium transistors that have been hand-selected to work in the germanium Fuzz Face circuit. Also included are 4 metal film resistors to use in the circuit. In most cases, the values have been modified from the stock values slightly to ensure that the collector of Q2 biases to roughly -4.5V. A data sheet containing the schematic and the resistor values is included so that you can use your own resistor type if you would prefer. There is a range of bias voltages that can sound nice in a Fuzz Face, and voltages in original units varied. These transistors have been tested with bias voltage, sound, and noise level in mind. Note that due to a variety of factors such as battery/PSU voltage, temperature, and component tolerance, the voltage on the collector of Q2 may not measure at exactly -4.5V, but it should be close in a properly-built circuit.
$24.95
Vacuum Tube Set - for calibrating TV-7 Testers
This is a set of measured vacuum tubes for use in TV-7 vacuum tube tester calibration. The values for each vacuum tube will be measured and included for the purpose of calibrating your own TV-7 tester at home. Steps for this calibration can be found online. Three tubes will be included:
  • 6L6
  • 6AU6
  • 12AT7

These tubes are tested at the following settings: Tube Filament Settings Bias Shunt Range 6L6 6.3 HS5-3481 23 0 D Tube Filament Settings Bias Shunt Range 6AU6 6.3 ET1-5672 16 0 B Tube Filament Settings Bias Shunt Range 12AT7 12.6 EV7-6080 10 0 C Note that brands are not guaranteed to match photograph.
$75.00
Capacitor - Mallory, 630V, 150s, Axial Lead
Tubular metalized polyester film construction
  • ±10% tolerance
  • Axial leads
  • Non-Inductive, Self Healing

Please Note: Color of capacitor may vary from one production run to another.
Starting at $1.19
Capacitors - Orange Drop, 600V, Polyester
Rated for 85°C operation. Polyester film capacitor with radial leads. ± 10% tolerance. Features a long history of proven reliability, a low dissipation factor, excellent stability, and a virtually linear temperature coefficient.
Starting at $0.85
Capacitor - 600V, 715P Series, Polypropylene
Rated for 85°C operation. Polypropylene film capacitor with radial leads. ± 5% tolerance.
Starting at $1.12
Capacitor - 400V, 716P Series, Polypropylene
High performance version of the popular 715P series. They are made from polypropylene film and foil with pure copper leads, making them ideal for high pulse current applications. Rated for 85 degrees celsius operation ± 5% tolerance. Straight radial leads, minimum 1.25" length.
Starting at $1.25
Capacitor - 600V, 716P Series, Polypropylene
High performance version of the popular 715P series. They are made from polypropylene film and foil with pure copper leads, making them ideal for high pulse current applications. Rated for 85 degrees celsius operation ± 5% tolerance. Straight radial leads, minimum 1.25" length.
Starting at $0.95
Capacitor - F&T, Multi-Section, Electrolytic
High quality multi-section can capacitors from F&T. These capacitors are similar to the LCR caps found in many Marshall and Hiwatt amplifiers. The body has a 1-⅜" diameter and a 2" length. A 1-⅜" mounting clamp is required. Made in Germany.
Starting at $10.95
Knob - Phenolic, Set Screw, Premium RCA Style, Skirted, Pointer
Phenolic skirted knobs with a set screw and brass insert. These unique knobs closely match the RCA style of knobs used on vintage test equipment, radios, studio consoles and other equipment. They are sometimes referred to as fester knobs. The RCA style knobs feature an inlay indicator line. Fits ¼” (6.35mm) pot shafts. 22mm Skirt:
  • Height: 0.495in. (12.6 mm)
  • Diameter: 0.875 in. (22 mm)
  • Fits ¼" shaft with set screw

26mm Skirt:
  • Height: 0.656 in. (16.7 mm)
  • Diameter: 1.02 in. (26 mm)
  • Fits ¼" shaft with set screw

33mm Skirt:
  • Height: 0.792 in. (20.1 mm)
  • Diameter: 1.293 in. (33 mm)
  • Fits ¼" shaft with set screw

40mm Skirt:
  • Height: 0.865 in. (22 mm)
  • Diameter: 1.568 in. (40 mm)
  • Fits ¼" shaft with set screw
Starting at $2.55
Capacitor - Mallory, 400V, 150s, Axial Lead
Mallory axial capacitors rated for 400V. The available values are smaller in size than the 630V versions for builds where less space is available. These are also a great choice for use as guitar tone capacitors over the larger 630V versions. The Type 150 series axial lead metallized polyester non inductive capacitors are available in bulk or on tape and reel for automatic insertion. Type 150 is a general purpose capacitor for use in blocking, bypass, decoupling, smoothing and some timing applications. Features
  • Epoxy end fill meets UL94V-0
  • Non inductively wound
  • Flame retardant outer wrap meets UL510
  • Non polar
Starting at $1.35
Capacitor - Orange Drop, 1600V, Polypropylene
Radial lead, polypropylene film capacitor. ± 10% tolerance. Features a long history of proven reliability, a low dissipation factor, excellent stability, and a virtually linear temperature coefficient.
Starting at $1.49
Wire - Weico, 22AWG Stranded, Top Coat Pre-Tinned, 600V, 50 feet
Colors Available:
High quality 22AWG wire from Weico featuring a topcoat of solder over the strands. This wire is pre-tinned in the sense that a coating of solder is already applied, bonding the individual strands together so no additional tinning is required.
$12.50
Footswitch - 3PDT, Alpha, PC Mount
High quality PCB mount 3PDT footswitch from Alpha. The Alpha 3PDT is a great choice for a durable and reliable footswitch. Mounting nuts, washer, and lockwasher included.
  • Bushing Length: 11.5mm
  • Threading: M12 x 0.75
  • PCB mount pins
$4.30
On Backorder
Diode - Zener, 5 Watt, ±5% tolerance
5W zener diodes that are great for use in tube amps. These are commonly used to drop B+ voltages for tube modification compatibility or to create low power modes for the amp. A zener is a semiconductor device that, above a certain reverse voltage(the zener value) has a sudden rise in current. If forward biased, the diode is an ordinary rectifier. When reverse biased, it exhibits a sharp break in its current-voltage graph. Voltage across the diode remains essentially constant for any further increase of reverse current.
Starting at $0.55
Footswitch - 3PDT, Alpha, Latching, Solder Lugs
High quality Alpha 3PDT footswitch with solder lugs. The Alpha 3PDT is a great choice for a durable and reliable footswitch. Mounting nuts, washer, and lockwasher included.
  • Bushing Length: 11.5mm
  • Threading: M12 x 0.75
  • Solder Lugs
$4.30
Power Jack - Cliff, DC Panel Mount, Rear Mount, 5.5mm External, 2.1mm Internal
High quality ½" panel mount DC jack with solder lugs from Cliff Electronic Components. This jack is rear mounted which makes troubleshooting and repairs simpler since the jack does not need to be desoldered if the circuit needs to be removed from the enclosure. For barrel plugs with a 5.5mm external diameter and 2.1mm internal diameter. Three solder lugs are available for tip, ring, and switch. Mounting nut included.
$1.35
Wire - Weico, 24AWG Stranded, Top Coat Pre-Tinned, 300V, 50 feet
Colors Available:
High quality 24AWG wire from Weico featuring a topcoat of solder over the strands. This wire is pre-tinned in the sense that a coating of solder is already applied, bonding the individual strands together so no additional tinning is required. This wire is ready to go as soon as it is cut and stripped making assembly that much easier. Rated at 300V and offered in a variety of colors, this wire is a great option for a variety of different projects.
$8.95
Banana Jack - Johnson Cinch, For 4mm Plugs, Panel Mount
Colors Available:
High quality banana jacks with tinned brass contacts and strong nylon housings. These jacks come in a wide variety of colors and work well with any 4mm banana plug. Cinch Johnson banana jacks are used in test equipment, audio equipment, as well as modular synthesizers such as DIY Buchla, Serge, and others. Features:
  • Formed brass contacts
  • Bright tin finish
  • Durable nylon 6/6 body
  • Nickel plated nut
  • 0.010Ω maximum contact resistance
  • Keyed mounting with two flatted sides
$1.65
Binding Post - PCB Type, Gold Plated
Colors Available:
Accepts standard banana plug, test and phone tip plugs, spade lugs, alligator clips, and bare wire. One plug per package. Gold plated. Multiple color options available.
$3.99
LED - 5mm diameter, diffused lens, 5 mCd
Colors Available:
5mm (T-1 ¾) diffused LED’s. Great for use in pedal builds and other applications where a tinted and diffused indicator is needed. Multiple colors available.
  • 5mm size
  • Tinted and diffused
  • Multiple colors available
  • Package of 5
$0.75
package of 5
Transformer - Hammond, High Voltage Plate & Filament, Vertical mount
  • Vertical Mount. For Horizontal Mount, see P-T263-Z
  • Primary 115 VAC, 60 Hz. - except as noted
  • Enclosed, 4 hole, chassis mount.
  • Minimum 6" long leads.
  • Units can be run full wave bridge or full wave C.T.
  • Class A insulation (105 degrees C).
  • Hi-Pot test of 2,000V RMS.
  • Conservative designs - CSA certified (209651).
Starting at $64.90
Save 7%
Originally: $69.95
Partially Out of Stock
Note: P-T274AX: 720 V C.T. @ 138 mA is a special order item.
Capacitor - Mallory, 100V, 0.68 µF, 150s, Axial Lead
0.68uF Mallory axial capacitors rated for 100V. This value is popular for cathode bypass capacitors in many vintage Marshall amps. The 8.5x20.5mm size works well for turret board builds of these classic amplifiers. The Type 150 series are axial lead metallized polyester non inductive capacitors. Type 150 is a general purpose capacitor for use in blocking, bypass, decoupling, smoothing and some timing applications. Features
  • Epoxy end fill meets UL94V-0
  • Non inductively wound
  • Flame retardant outer wrap meets UL510
  • Non polar
$3.95