Tools

Tool Set - Rocket Sockets, Pepers’ Pedals, Complete Set
Rocket Sockets by Pepers' Pedals allow for the tightening of various nuts for jacks, potentiometers and switches on guitar effects pedals without scratching the enclosure and damaging the graphics or paint as the typical metal tools will do.
$14.95
Staking Tool Set - Anvil and Punch, for Eyelets and Turrets
Staking tool set that includes both the anvil and swage/punch. The set works with standard turret and eyelet sizes commonly used in amplifiers. The anvil also can be used with Y style turrets.
$12.55
Truss Rod Wrench - Phillips Head / Cross Head
High quality Phillips head truss rod wrench. This Japanese made wrench is the perfect tool for cross slotted truss rod nuts found on many Fender® necks. The compact 9mm diameter head has a thin 11mm width allowing for adjustments without removing the neck
$10.16
Tool - Slotted Nut Driver, for Qingpu Jacks
Simple and easy to use nut driving tool for the slotted nuts found on Qingpu jacks that are commonly used in Eurorack modules. The tool anchors into the sleeve of the jack ensuring no slippage when in use, protecting the faceplate from accidental damage. The two grip holes are cut to the size of M2.5 and M3 hex nuts and can be used in a pinch to tighten nuts of those sizes, or to hang your tool on a keyring! One side of the tool works with Mod "Top Brass" nuts and slotted W-QP-NUT-K nuts used on W-QP-518MA, W-QP-419GR, and W-QP-518MA-BM. The other side works with slotted W-QP-NUT-PJ-R nuts used on W-QP-PJ3410. Either side will work with Befaco Bananuts for 3.5mm jacks (W-BNUT-X). The nut driving tool is made of steel.
$4.30
Cutters - Xcelite, Shearcutter, General Purpose
5" Overall Length, 3/4" Jaw Length. Great for cutting wire and component leads, etc. Product Features:
  • Low profile, general-purpose cutter
  • Superior blade by-pass shear cutting action
  • Better cuts with half the effort
  • Greatly reduced mechanical shock delivered to the work
  • Features red grips
  • Flush cuts soft wire up to 20 AWG (0.8mm)
$15.95
Staking Tool - for Eyelets and Turrets
Turret staking tool for use with our turrets (S-HTUR-SG-2X, S-HTUR-SG-3X, S-HTUR-PR-3S).
For anvil see S-T1717
For smaller staking tool, see S-T1714
Directions:
  • Drill 1/8" hole
  • Insert eyelet
  • Flip board over on to a hard service
  • Center staking tool over the eyelet
  • Strike staking tool with hammer to clamp eyelet to board
$14.95
The Nibbler - cutter for square holes
Instructions
  • Simply drill 3/8" hole insert cutting head and compress handles.
  • Gives you the ability to make square holes for fuse holders, special connectors displays etc.
  1. Material to be nibbled is placed in the gap between the punch and blade channel.
  2. By squeezing the handles together, the punch will move down into the channel, cutting out a slug of metal.
  3. A scribe line can be followed by looking down on work in this position.
$6.99
Adjustment Tool - Bourns Trimpots, H-90
Bourns trimmer adjustment tool. This tool is compatible with both the R-VT96Y-X multiturn trimmers and the R-VT62P-X single turn trimmers. The recessed end is especially helpful when used with the 3296Y trimmers to avoid slipping off of the screw adjuster. Features
  • Meets UL 94V-0
  • Pocket clip
  • For use on most trimmer shafts/rotors
  • Recessed end for use with extended shafts
  • RoHS compliant
$4.95
Brush - Befaco, Gear Duster
Gear duster from Befaco. The Befaco Synth Duster is a great tool for getting dust off of faceplates and other hard to reach spots on your equipment. The super soft bristles can gently clean around pots, jacks, and other hardware.
$12.95
Center Punch - Spring Loaded, Adjustable Force
Spring loaded center punch with an adjustable force for aligning pilot holes when drilling into materials. The large handle makes the push-to-strike action simple and accurate. Rotating the red handle adjusts the force amount.
$6.45
Tool - GrooveTech, Jack / Pot Tool
Instrument and amp jacks are notorious for coming loose. And with a shallow nut and recessed cavity, access can be challenging. Until now, that is. The GrooveTech Jack and Pot Wrench provides three thin-wall sockets - ½", 7/16", and 12mm - in a compact four-inch tool to handle the most common sizes of jacks and pots on instruments, amps, and other audio gear. Add a dab of threadlocker, and you'll probably never have to deal with that loose jack again. Sockets are pro-grade with a dazzling polished chrome finish.
$16.95
Alignment Kit - GC Electronics, for color TVs
Contains 6 different tools for all standard adjustments. Tools are Delrin with the exception of the potentiometer adjustment tool which is Nylon.
Tools are:
  • 8282 Zenith type Hex/Screwdriver
  • 8606 5" Hex wrench
  • 9091 Hex iron core tool
  • 9300 5" Double sided hex tool
  • 9304 Hex screwdriver combination
  • 8608 Potentiometer Adjustment Tool
$8.45
package of 6
Multi-Tool - GrooveTech, for Guitar and Bass
The GrooveTech Guitar/Bass Multi-Tool has everything you need to give your guitar or bass a full setup—and it’ll all fit in your pocket or your gig bag. For truss rod adjustments, this multi-tool is equipped with three ball-end hex wrenches for standard nuts and a a 5/16” nut driver for Gibson-style nuts. Additional hex wrenches cover bridge and tremolo adjustments, and if you need to work on an instrument with vintage-style saddle screws, the 2.5mm slotted screwdriver is ready to go. Need to remove your pick guard or neck plate or put on a new set of Straplok® Strap Buttons? The two Phillips screwdrivers will take care of these and other needs. Finally, the ruler will help you check neck relief and string action.
All wrenches are pro-grade, using heat-treated S2 steel with a polished chrome finish.
$16.95
Springs - Xcelite, replacement for S-TCN255
Replacement spring for S-TCN255 (Xcelite curved nose pliers).
$1.00
Tool - Better Setter, Pepers’ Pedals, Knob Alignment
The Better Setter tool is essentially a mini set square for control knobs ensuring the knobs are lined up perfectly every time. The U-shaped slot is fitted around the pot shaft and the adjustable straight edge is then aligned and set to the edge of the enclosure. The two white lines on the U-shaped slot can then be used to set the knob to the beginning or end of the pot’s travel. Works best with 7mm bushing potentiometers.
$12.95
Brush - Flat Chip, 2”, 1500, applicator
2 inch flat chip brush great for applying tolex glue or any other purposes. This brush features a 4.75 inch wood handle.
$2.95
Desoldering Pump - Manual, for removing solder
Handheld desoldering pump for solder removal. The enhanced dual spring-loaded piston creates a powerful vacuum for easy removal of molten solder. The static free tip is self cleaning and made from a clog resistant material. The aluminum body is lightweight and durable.
$16.95
Guitar Nut Cube - for adjusting guitar nuts
Unique tool for the easy removal and adjustment of potentiometers and switches from guitars
$15.95
Wrench - GrooveTech, Soundhole Truss Rod
GrooveTech soundhole truss rod wrench for acoustic guitars. Acoustic guitar truss rods need adjustment just like electrics, but manufacturers sure don't make it easy. Access is typically through the sound hole, sometimes through a brace to an unseen nuts. These wrenches allow quick access to nuts on most makes and models of acoustics, with a precision ball-end tip for easy fit, extra length on both segments of the blade, and an oversized handle for confidence when making adjustments. Professional-grade.
Starting at $11.95
String Cutters - GrooveTech, for guitar and bass
GrooveTech developed the String Cutters specifically for Guitar and Bass strings. Guitar and bass strings are made of hardened stainless steel or nickel with thicknesses as high as 3mm. Ordinary diagonal cutters are designed for soft copper, and thus fail miserably when used on strings. GrooveTech String Cutters were developed specifically for this application, using a proprietary heat-treatment process. Despite its compact five-inch length, even “B” bass strings cut easily and your days of dented blades will be a thing of the past. Vinyl grips feel great in your hands.
$11.95
Tool - Hand Riveter, 3/32”, ⅛”, 5/32”, and 3/16”
Hand riveter with four nose pieces and 100 rivets. The included nose pieces fit 3/32”, 1/8”, 5/32”, and 3/16” rivets. A small wrench is tucked into the grip so users can quickly change the nose pieces as needed. This set includes 100 rivets; 25 in each of the compatible sizes.
  • 3/32”, 1/8”, 5/32”, and 3/16” nose pieces
  • All-steel construction
  • Comfortable vinyl grip
  • Easily switch between nose sizes using the included wrench
$9.95
Wire Stripper / Cutter - 8", 10-24 AWG
Heavy duty wire strippers with additional cutting and crimping features. Capable of stripping 12 through 24AWG stranded wires and 10 through 22AWG solid wires, these strippers can handle most wires used in electronics.
$15.95
Caliper - Digital, highly-accurate for luthiers
This Luthier's Digital Caliper has a custom jaw notch for accurately measuring fretwire crown height (the height above the fretboard). This is essential for comparing new wire to original wire. And there's a notch on the depth gauge to measure fret height on the instrument.
  • Measures fret height before AND after fret installation
  • Accurate readouts in inches or millimeters
  • A must for all precision guitar work
$44.95
Wrench - Befaco, Bananut Driver
Custom wrench tool for Bananuts. The two pegs slot into the notches on the Bananuts for an easy installation. Note: This wrench is only compatible with Befaco Bananuts
$6.50