You are here

Tools

Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(15 pages)
S-T263Knob & Bushing Puller - for Easy Removal From Guitar
The Knob and Bushing Puller's clear acrylic housing has a rubberized base to help protect the guitar's finish. The square unit has 2 ends- one end for pulling knobs, the other end can work with the attached hardware to easily extract Gibson, Schaller or Gotoh bridge and tailpiece stud bushings, without damaging the guitar

Includes 6 bolts and 2 flat washers for pulling various bushing threads:

  • 5/16-20
  • 5/16-24
  • 5/16-18
  • 10-32
  • M5
  • M6
  • M8


Roughly 0.65" clearance between the bottom of the knob and the top of the guitar required for knob puller attachment.
$37.00
$33.30
You save: 10%
Click to read more
S-F504XAdhesive - Bob Smith Industries, Maxi-Cure Extra Thick

Bob Smith Industries ™ Maxi Cure ™ Extra Thick Gap Filling Cyanoacrylate. A must have for luthiers! Maxi Cure ™ is the highest viscosity CA we have available and is great for extreme gap filling and finish fills. It can be carved with a knife or razor blade and sanded and feathered to form a finish which makes it great for chip repairs. The extra thick viscosity of Maxi Cure ™ also allows longer repositioning time than other glues (10-25 sec.) Apply Maxi Cure ™ in a coil pattern to one of the parts to be glued, spread glue evenly, then assemble parts. Hold or clamp firmly for 30-60 seconds. To speed up curing time use the Insta-Set accelerator! (S-F506)


$5.50
Starting at $4.95
You save: 10%
Click to read more
P-PC-ST1StripBoard - Single Sided, Size 1, Uncut

Prototyping circuit board with a standard long strip pattern where tracks run the length of the board. The long tracks are convenient for power and ground rails, and for signal buses. Strips can be cut as needed to make smaller tracks and circuit pads and the board has 0.1" hole spacing for DIP integrated circuits/ headers as well as other parts. Higher quality than traditional stripboard, the holes are drilled, not punched.


$2.95
$2.66
You save: 10%
Click to read more
P-PC-PAD1PadBoard - Size 1, Double Sided, Plated Holes

Prototyping circuit board that has a general purpose pad-per-hole pattern making it great for general purpose analog and digital use. It is a double-sided board with plated holes, which allows components to be easily soldered to either side of the board. A square pad is provided every 5th hole, which makes it easy to align components on the top and bottom of the board. An anti-tarnish coating protects the copper for a long shelf-life and provides easy soldering.



For fastening your project to a surface see our adhesive standoffs (S-H190-X)



Features:



  • Pad-per-hole prototyping board with plated-thru holes. A square pad every 5th hole makes it easy to align components on top and bottom.
  • Double-sided high-quality FR4 glass-epoxy circuit board with plated holes. Components can be soldered to either side.
  • 1oz/ft2 copper with an anti-tarnish coating for easy soldering.
  • 31 x 19 holes, 0.037" holes are drilled on 0.1" (2.54mm) centers. Four 0.125” mounting holes.
  • Size 1 = 1.97 x 3.15in (50 x 80mm), 1/16" thick (1.6mm)

$2.95
$2.66
You save: 10%
Click to read more
S-T203String Spacing Ruler - Steel

Get accurate string spacing without the use of complicated tools with this easy-to-use String Spacing Ruler. "Mark outer string locations with pencil lines (high and low E strings on guitars), usually about 1/8" in from fingerboard edges. Turn ruler over (use marked side). With wide spacing toward bass side, narrow spacing toward treble side, find group of marks (six for guitar) which best fit your two pencil lines. Use a razor knife or thin mechanical pencil to mark the string positions through the ruler's slots.


$19.95
$17.96
You save: 10%
Click to read more
S-T309String Action Gauge - Dunlop, System 65

The Dunlop System 65 String Action Gauge is a precision measurement tool for setups and adjustments. The gauge includes both metric and imperial measurements on opposite sides.


$11.95
$10.76
You save: 10%
On Backorder
Click to read more
S-F506XAdhesive - Bob Smith Industries, Insta-Set Foam, Pump Spray

Bob Smith Industries INSTA-SET™ CA (super glue) Accelerator. INSTA-SET™ is a catalyst which acts as an accelerator that allows CAs to quickly cure in thick layers by enhancing the alkaline conditions during polymerization. INSTA-SET™ in a spray bottle is normally used to cure the CA that flows from joints when parts are pressed together. Applying an additional bead of thick CA along a seam and then curing it with INSTA-SET™ significantly enhances a joint’s strength. For difficult to bond materials, INSTA-SET™ can be applied to one surface and CA to the opposite surface. When brought together, they will bond instantly. INSTA-SET™ is formulated with a strawberry scent and activates CA in 6 to 8 seconds without any degrading of the CAs strength, which can occur with many other accelerators. It is compatible with all surfaces, even clear plastic and white foam.



  • Convenient pump spray (2oz.

$5.95
Starting at $5.35
You save: 10%
Click to read more
S-TVBVTool - Vacuum Base Vise, 40mm
Mini vise. Great for securing small, light-weight components like potentiometers, tube sockets and switches while soldering or de-soldering. Clamp opens to 40 mm max.
$6.95
$6.26
You save: 10%
Click to read more
S-T200XString Action Gauge - Measurement Tool

A stainless steel pocket-sized String Action Gauge that's perfect for obtaining quick and accurate action measurements for acoustic and electric instruments. A must have in a busy repair shop! Measurements taken using this gauge include:



  • Saddle height/slot depth
  • String height
  • Nut height/slot depth
  • Pickup pole piece height/string to pole piece distance
  • Fret slot depth(unbound fingerboards only)


Plus more! The back includes a useful fraction/metric/decimal conversion chart that saves you time. Available in metric or in imperial models (sold individually)


$16.95
$15.25
You save: 10%
Click to read more
S-T214-XFret Files - for Filing Fret Crowns

Solid steel crowning files with dual cutting edges for precision fret crowning. These should be in any luthier’s tool kit!



  • Made of solid steel
  • Soft rubber coating on the handle
  • Double sided (both sides are the same size)
  • 4-3/16” cutting surface
  • Available in three sizes to cover most fret sizes (small,medium,large)

$28.95
Starting at $26.05
You save: 10%
Click to read more

Pages

(15 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Tools