Tools

Bias Master™ - TAD, tube tester, with 4 probes
Bias Master™ system BM4 Measures Bias current of the vacuum tubes in your amp. Includes 4 probes and english/german operation manual. The Bias Master™ allows you to monitor the bias current safely and easily. While adjusting the Bias control pot of your amp, the Bias Master™ shows the actual result. This lets you set and evaluate the full reasonable biasing range your amp and tubes offer to find and set your personal perfect choice.
$228.95
Hot Air Station - Atten, ST-862D, High Power, 1000W
The Atten ST-862D high power hot air station. The ST-862D hot air station offers powerful heating with plenty of airflow in an affordable package with no compromises. Professionals have done detailed comparisons with machines more than three times the price and have found that the ST-862D performs just as well or better. The ST-862D is a great choice for beginners looking to learn SMD soldering and is also a great choice for those looking to upgrade their current setup.
$214.95
Generator - Lodestar, Audio Frequency
The oscillation frequency range of this audio generator is between voice frequency band and super voice frequency band. Square and sine wave. 10K ohm input impedance, 10 V rms maximum input voltage. 600 ohm output impedance. Equipped with synchronized input terminals, enabling the high power output signas to be accurately controlled by small signals. comes with test lead and ground lead. 5.9" high x 9.8" wide x 5.1"deep.
$167.36
Save 10%
Originally: $185.95
Soldering iron station - Weller, WE 1010, 70W, digital display
The Weller WE1010 is an excellent soldering station for professional use and beginner hobbyists alike. With increased power and stability, the WE1010 is an upgrade in many ways for users of the WES51 and WTCPT soldering stations.
$154.95
Fret Slotting Miter Box - for guiding fret saws
Use this Fret Slotting Miter Box to accurately cut fret slots with a fretting handsaw. The ball-bearing guides make sawing easier and faster; they hold your fret saw perpendicular to the fingerboard and can be adjusted to match the blade precisely. You can quickly slot any board up to 3"" (76.2mm) wide, with adjustable depth of cut for any fret wire. You always have an unobstructed view of your work.
Made of rugged aluminum and 12" (304.8mm) long, this miter box has convenient mounting holes for firm attachment to your workbench, the mounting screws and spanners are included. Instructions also included.
$135.00
Nut File - Edge-Cut, for guitar, 10 sizes
Edge cut nut files in popular gauges specially designed for slotting nuts. These files cut a smooth, round bottom slot. Also great for slotting tune-o-matic bridge saddles! Always try and use a file gauge that’s not more than a couple thousandths larger than the gauge of string you are using. Smaller files can be used to create wider slots by using a side-to-side movement while cutting.
  • 4-1/2” cutting edge
  • Double sided (both sides are the same gauge)
  • Set of 10 files
  • Made In Japan

Set contains one of each size:
  • 0.010"
  • 0.013"
  • 0.016"
  • 0.024"
  • 0.028"
  • 0.032"
  • 0.036"
  • 0.042"
  • 0.046"
  • 0.056"
$120.70
package of 10
Fret Press - Handheld, 4 cauls, for seating frets
Handheld fret press is a professional fretting tool that gives you finer control over the pressure needed to seat a fret into the slot - you can actually feel it seating! It eliminates complicated clamping setups, so your press-in fret jobs go faster. There's a self-leveling upper caul that adjusts easily to any neck. Used with radius inserts (S-T261) to press frets into guitar fret boards. This method is preferred by many as an alternative to hammering the frets in. Includes 4 interchangeable support cauls.
$109.95
Bench-top smoke absorber - Weller, for soldering
Keep those fumes out of your face while soldering with this benchtop smoke absorber.
  • Removes flux fumes from soldering workbench
  • Great for workspaces using more active fluxes used with lead-free solder
  • Fumes are absorbed by the replaceable carbon-activated filter
  • Includes one replacement filter (S-TWSA350F)
  • Stand allows the smoke absorber to be adjusted to varying angles
  • Fan is quiet and will not add significant noise to the workspace
  • ESD safe
  • Air Flow Volume: 1370 l/min
  • Wattage: 20 watts
$109.95
Solder - Kester 48, .031", Flux 66, Lead-free 1 lb Spool
Lead free solder, Sn96.5Ag3.0Cu0.5, 031" diameter, rosin flux, core 66. Kester SAC305 48 Activated Rosin Flux for cored solder wire was developed for lead-free applications to enable soldering of most common metals.
$99.95
Soundhole Kit - Router Base and Jig
This kit consists of the precision router base for Dremel tools along with the routing jig for soundhole & rosette. Kit includes:
  • S-T235
  • S-T256

The precision router base is a stable and versatile way to support your Dremel tool. This base is the best way to hold a Dremel for freehand routing, inlaying, widening fret slots, and more. Made of brass, aluminum and machined steel, it features precision cutting depth adjustment with large thumbwheels to eliminate guesswork.
  • Excellent control
  • Easy installation
  • Accurate freehand routing

Operation information for the precision router base: To install - simply unscrew the threaded collar on the nose of the Dremel and screw the Dremel directly into the Precision Router Base. Each turn of the large knurled thumbwheels adjusts your Dremel's cutting depth by .035"" (.889mm).
$99.65
On Backorder
Fret File - 600 grit, 3 radiuses, diamond, for Crowns
600 grit diamond-plated file. 3 different, (small, medium, large) radiuses in one file. 130mm file length, 230mm total.
$96.95
Fret Saw Guide - for Ensuring Straight Cuts
Three neodymium magnets on each end to ensure a straight cut at a right angle. The saw guide can adjust 0mm to 4.7mm slot depth by sliding the frame. The slide frame side has scale marks representing 1mm of depth. For use with S-T254.
$93.25
Vacuum Tube Set - for calibrating TV-7 Testers
This is a set of measured vacuum tubes for use in TV-7 vacuum tube tester calibration. The values for each vacuum tube will be measured and included for the purpose of calibrating your own TV-7 tester at home. Steps for this calibration can be found online. Three tubes will be included:
  • 6L6
  • 6AU6
  • 12AT7

These tubes are tested at the following settings: Tube Filament Settings Bias Shunt Range 6L6 6.3 HS5-3481 23 0 D Tube Filament Settings Bias Shunt Range 6AU6 6.3 ET1-5672 16 0 B Tube Filament Settings Bias Shunt Range 12AT7 12.6 EV7-6080 10 0 C Note that brands are not guaranteed to match photograph.
$75.00
Fret Bender - for creating radius in or flattening Fret Wire
Multi-functional Fret Bender - bend or staighten either bulk fretwire or pre-cut short piece fret wire precisely and quickly! For bending fret wire, crank a length of fretwire through the fret bender, and it comes out curved and ready to install in a radiused fretboard. Get a perfect bend on enough wire for a whole guitar in just seconds. Precisely radiused fretwire makes your fretwork fast, accurate, and professional.
Can be mounted to a workbench by using the two 5/16” bolt holes.
$69.95
Nut Slotting Gauge - Digital, luthier tool
Digital Nut Slotting Gauge. Accurately measure the guitar string height over the first fret with the digital version of this handy luthier’s tool. Display measurements in inches or mm with an accuracy of 0.0005” (0.01 mm).
$66.95
Fret File - Diamond, offset, for dressing and shaping frets
Diamond fret file with offset shape for more comfortable fret dressing and improved clearance over the guitar body at high frets. Both full length concave filing grooves (for medium and wide fretwire) uniformly coated with micro industrial diamond particle.
$66.95
Probes - TAD, for Bias Master™, set of 2
Bias Master™ set of adapter probes for testing other types of tubes. For use with the S-TBM4-X Bias Master™ system.
Starting at $65.95
package of 2
Tech Kit - GrooveTech, for Guitar Player
The GrooveTech Guitar Player Tech Kit has everything you need to take care of your guitar with confidence, featuring top-shelf tools that have been optimized for just about every make and model of guitar. For your truss rod and string action adjustments, take your pick from the 11 color-coded hex wrenches—gold for metric, black for imperial. Truss rod sizes come with ball ends for hard-to-reach nuts. Check your neck relief with the capo and thickness gauge and your string action with the ruler. The 6-in-1 screwdriver, which comes with two Phillips bits, two slotted bits, and two nut drivers, allows for easy tightening or removal of various hardware pieces. Remove your strings in no time with the string cutters—they’ll cut through even bass strings with ease—and then string up again with a fast-action string winder. Tools are guaranteed with a limited lifetime warranty. Never worked on your instrument before?
$64.95
File - Diamond, for Frets, Straight
Double sided diamond fret file. Easily the best choice for fret crowning, diamond files cut in two directions (push and pull) rather than one with no chatter giving you a smoother fret after the crowning process File cutting surface is impregnated with diamonds to give you a smooth cut with long lasting durability.
  • Made of solid steel with diamond cutting surface.
  • Soft rubber coating on the handle
  • 5-3/4” cutting surface
  • Double sided to cover different fret sizes
$62.95
Tape - Copper Foil, for Shielding, 98ft Length Roll
Conductive copper foil tape for shielding guitar cavities, amplifier cabinets, or elsewhere. This tape features a strong adhesive backing and soldering directly to the surface is easy and results in a strong bond. Sold in 98ft rolls.
Starting at $59.95
File Set - for Nut And Saddle Shaping
Set of files for control over shaping nuts and saddles.
  • Half-round shape
  • Flat shape
  • Triangle shape
$54.95
package of 3
Routing Jig - for Soundhole & Rosette
Soundhole and Rosette routing jig. Adjustable from 2” diameter to 6” diameter. Includes two hex adjustable M4x0.70 countersunk screws for attaching a router base, one registration pin (4 mm diameter) and three hex keys: 2.5 mm, 2.0 mm, 1.5 mm. Use with precision router base support for Dremel tool (S-T235).
$54.95
On Backorder
Nut Files - Double Edge, for guitars, 3 sizes
Double edge nut files featuring popular guitar gauges specially designed for slotting nuts. Each set of files is specifically designed for guitars of a particular type. This set of three files will cover the work of six and cuts a smooth round bottom slot. Always try and use a file gauge that’s not more than a couple thousandths larger than the gauge of string you are using. Smaller files can be used to create wider slots by using a side-to-side movement while cutting.
  • 4” cutting edge
  • Set of 3 files
  • Made In Japan
Starting at $53.65
package of 3
Partially Out of Stock
Solder - Kester 63 / 37, 1 lb spool, 0.031" diameter
(63/37 Rosin Core) - ..031" Diameter, 1 lb Spool, contains lead alloy. Kester 44 Rosin Flux is an activated rosin formula for use in flux-cored solder wire. Kester 44 Rosin Flux has virtually dominated the field of activated rosin core solders for well over four decades. An outstanding performance feature of this flux is the “instant-action” wetting behavior.
$50.95