• Replacements for Fender Amps
• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

Output transformer upgrade for the Fender® part numbers 125A35A, 125A3A, and 022905 as used in the:

• Bronco (AA764, AB764, Blackface, Silverface)
• Champ (Tweed, 5C1, 5E1, 5F1, AA764, Blackface, Silverface, Vibro Blackface)
• Harvard (6G10)
• Princeton (Tweed, 5B2, 5C2, 5D2, 5E2, 5F2, 5F2A)

This upgraded transformer features both 4 ohm and 8 ohm taps on the secondary. The primary has two impedance options for lower voltage (5K) and higher voltage (8k) models.

Specifications

• Power: 8 W
• Primary Impedance: 5,000 Ω single-ended
• Secondary Impedance: 8 Ω
• Primary DC Resistance (Red to Blue): 230 Ω
• Mounting Centers: 2.375"
• Mounting Type: U-bracket
• Weight: 0.7 lbs

• Designed for push-pull tube output circuits.
• Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
• Frequency response 30 Hz. to 30 Khz. at full rated power (± 1 db max. - ref.

• Replacements for Marshall Amps
• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

Specifications Output 8 W Primary Impedance 4,000 to 9,000 Ω Mounting Centers 2.375" Weight 0.7 lbs

• Designed for general purpose or replacement use in push-pull tube output circuits. (For single ended use, see our 125 SE series - optimized for single ended tube output circuits).
• Frequency response: 150 Hz. - 15 Khz (± 1db max. ref. 1 Khz).
• Open style with minimum 5" long primary leads, secondary solder lugs for convenient secondary connections.
• Tables provided with transformer listing 90 pre-calculated impedance ratios.

• Designed for general purpose or replacement use (not Hi-Fi), in single ended, tube output circuits.
• Frequency response: 100 Hz. - 15 Khz (± 1db max. - ref. 1 Khz). (For full frequency response (20 Hz. to 20 Khz.) - see P-T1627SE).
• For push-pull output use, see P-T125A - optimized for push-pull tube output circuits.
• Open style with minimum 12" long primary & secondary leads leads.
• All sizes use butt stacked cores (using 29M6 steel) with an air gap, to reduce D.C. core saturation.
• Primary impedance range from 2,500 to 10,000 Ohms.
• Secondary impedance range from 4 to 32 Ohms.

Part No.
Audio Power
Max D.C. Bias
Dimensions (Inches)


A
B
C
D
E
G Mtg.

• Replacements for Marshall amps
• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

Fender Original Hot Rod Deluxe and Blues Deluxe output transformer. 40 watts. Equivalent to #050438.

• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
• See P-T290-FENDER-120-UP for upgraded 120 V transformers, P-T290-FENDER-240 for 240 V transformers

Warning: Not all amplifier models of the same name use the same transformer model.

Replacement reverb driver transformer for the Fender® part numbers 125A20B, 022921, and 037099. This is the standard reverb driver transformer used in most Fender amps that use a 12AT7 and transformer driven 4AB3C1B tank. Found in countless Fender® models including original and reissues of the following:

• Fender Princeton Reverb
• Fender Deluxe Reverb
• Fender Vibrolux Reverb
• Fender Pro Reverb
• Fender Super Reverb
• Fender Twin Reverb
• Fender Quad Reverb
• Fender Super Six Reverb
• Fender Vibrosonic
• Many others

Original Fender® reverb driver for Pro Reverb. Replacement for #037099. Warning: Not all amplifier models of the same name use the same transformer model. Please make sure the amplifier transformer which you are replacing has a Fender number matching the equivalent Fender transformer number listed here.
See P-TGR-001 for a generic Fender® style reverb driver.

Features

• Economical "open bracket" - channel mount.
• Tolerance of 15% on both inductance & resistance.
• Inductances measured at rated D.C.

Replacement choke for the Fender® part numbers 125C3A and 022707 as used in the Deluxe, Deluxe Reverb, Vibrolux, Vibrolux Reverb, 1964 Blackface 6G15 Reverb, and others. This choke is rated 4H 50mA DC.

Equivalent to Stancor A53-C. 1:3 ratio overall. Center tapped secondary may be used for push-pull grids.Specifications Max. Primary Current: 10 mA Impedance Primary to Secondary (Ohms): 10,000 to 90,000

• Vertical Mount. For Horizontal Mount, see P-T263-Z
• Primary 115 VAC, 60 Hz. - except as noted
• Enclosed, 4 hole, chassis mount.
• Minimum 6" long leads.
• Units can be run full wave bridge or full wave C.T.
• Class A insulation (105 degrees C).
• Hi-Pot test of 2,000V RMS.
• Conservative designs - CSA certified (209651).

Power transformer replacement for the Fender® part numbers 125P1B, 022772, and 66079B. This transformer offers two different B+ options for lower voltage or higher voltage builds. This transformer is used in versions of the:

• Bronco
• Champ
• Princeton
• Princeton Reverb
• Vibro Champ

Features

• 275V or 325V (650/550 VCT) B+ options at 100mA
• Center tapped 6.3V filament at 2.25A
• 5V filament supply at 3A
• For 120V 60Hz primary
• Standard 2.5” x 2” mounting centers