Transformers & Chokes
Transformer - Hammond, Output, replacement for Fender
- Replacements for Fender Amps
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $33.95
Transformer - Hammond, Guitar Amplifier, replacement for Fender, 120 V
Warning: Not all amplifier models of the same name use the same transformer model.
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
- See P-T290-FENDER-120-UP for upgraded 120 V transformers, P-T290-FENDER-240 for 240 V transformers
Warning: Not all amplifier models of the same name use the same transformer model.
Starting at $57.49
Transformer - Reverb Driver, for Fender® Amps, 125A20B Replacement
Replacement reverb driver transformer for the Fender® part numbers 125A20B, 022921, and 037099. This is the standard reverb driver transformer used in most Fender amps that use a 12AT7 and transformer driven 4AB3C1B tank. Found in countless Fender® models including original and reissues of the following:
- Fender Princeton Reverb
- Fender Deluxe Reverb
- Fender Vibrolux Reverb
- Fender Pro Reverb
- Fender Super Reverb
- Fender Twin Reverb
- Fender Quad Reverb
- Fender Super Six Reverb
- Fender Vibrosonic
- Many others
$13.95
Transformer - Fender®, Reverb, for Pro Reverb
Original Fender® reverb driver for Pro Reverb. Replacement for #037099. Warning: Not all amplifier models of the same name use the same transformer model. Please make sure the amplifier transformer which you are replacing has a Fender number matching the equivalent Fender transformer number listed here.
See P-TGR-001 for a generic Fender® style reverb driver.
See P-TGR-001 for a generic Fender® style reverb driver.
$28.95
Filter Choke - Hammond, Open Bracket
Features
- Economical "open bracket" - channel mount.
- Tolerance of 15% on both inductance & resistance.
- Inductances measured at rated D.C.
Starting at $16.75
Transformer - Output, 5W, 5k & 8k Primary Options, Upgrade for Fender® Champ
Output transformer upgrade for the Fender® part numbers 125A35A, 125A3A, and 022905 as used in the:
This upgraded transformer features both 4 ohm and 8 ohm taps on the secondary. The primary has two impedance options for lower voltage (5K) and higher voltage (8k) models.
- Bronco (AA764, AB764, Blackface, Silverface)
- Champ (Tweed, 5C1, 5E1, 5F1, AA764, Blackface, Silverface, Vibro Blackface)
- Harvard (6G10)
- Princeton (Tweed, 5B2, 5C2, 5D2, 5E2, 5F2, 5F2A)
This upgraded transformer features both 4 ohm and 8 ohm taps on the secondary. The primary has two impedance options for lower voltage (5K) and higher voltage (8k) models.
$19.95
Choke - 4H, 50mA, for Fender® 6V6 Amps, 125C3A Replacement
Replacement choke for the Fender® part numbers 125C3A and 022707 as used in the Deluxe, Deluxe Reverb, Vibrolux, Vibrolux Reverb, 1964 Blackface 6G15 Reverb, and others. This choke is rated 4H 50mA DC.
$11.95
Transformer - Audio Interstage, 10 mA
Equivalent to Stancor A53-C. 1:3 ratio overall. Center tapped secondary may be used for push-pull grids.Specifications Max. Primary Current: 10 mA Impedance Primary to Secondary (Ohms): 10,000 to 90,000
$16.95
Transformer - Hammond, High Voltage Plate & Filament, Vertical mount
- Vertical Mount. For Horizontal Mount, see P-T263-Z
- Primary 115 VAC, 60 Hz. - except as noted
- Enclosed, 4 hole, chassis mount.
- Minimum 6" long leads.
- Units can be run full wave bridge or full wave C.T.
- Class A insulation (105 degrees C).
- Hi-Pot test of 2,000V RMS.
- Conservative designs - CSA certified (209651).
Starting at $64.90
Save 7%
Originally: $69.95
Transformer - Power, 120V Primary, 325/275V / 6.3VCT / 5V Secondary, for Fender® Champ
Power transformer replacement for the Fender® part numbers 125P1B, 022772, and 66079B. This transformer offers two different B+ options for lower voltage or higher voltage builds. This transformer is used in versions of the:
Features
- Bronco
- Champ
- Princeton
- Princeton Reverb
- Vibro Champ
Features
- 275V or 325V (650/550 VCT) B+ options at 100mA
- Center tapped 6.3V filament at 2.25A
- 5V filament supply at 3A
- For 120V 60Hz primary
- Standard 2.5” x 2” mounting centers
$59.95
Transformer - Output, 8 W, Single Ended
Specifications
- Power: 8 W
- Primary Impedance: 5,000 Ω single-ended
- Secondary Impedance: 8 Ω
- Primary DC Resistance (Red to Blue): 230 Ω
- Mounting Centers: 2.375"
- Mounting Type: U-bracket
- Weight: 0.7 lbs
$20.85
Choke - 4H, 90mA, for Fender® 6L6 Amps, 125C1A Replacement
Replacement choke for the Fender® part numbers 125C1A, 022699, and 036468 as used in the Bandmaster, Dual Showman, Pro Reverb, Twin Reverb, Super Reverb, and others. This choke is rated 4H 90mA DC.
$18.95
Transformer - Hammond, High Voltage Universal Plate & Filament, Vertical mount
- Primary: Universal - 100, 110, 120, 200, 220,230, 240 VAC 50/60 Hz.
- NOTE: units are designed to operate with BOTH primary windings engaged.
- See primary wiring information under resources.
- Bias Tap: 50 VAC tap from high voltage secondary C.T. (except part number P-T379WX - uses a separate 60VAC 0.2 Amp winding).
- Highpot tested: 2,000 VAC
- Faraday Copper Primary Shield: Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries (shield is internally grounded to the end bell).
- Windings: Concentric wound for low stray field and low noise.
- Models: This series is an upgrade from our P-T263-X range of units PLUS 2 models designed specifically for 300B tubes (Part Number P-T300BX) and 2A3 tubes (Part Number P-T302AX).
- Finish: Black powder paint to match our P-T1650X series of output transformers Units can be run full wave bridge or full wave C.T.
- Conservative designs - CSA certified (209651).
Starting at $90.06
Save 4%
Originally: $93.97
Choke - Hammond, for Fender Bandmaster, Dual Showman, etc.
Replacement for Fender Bandmaster, Dual Showman, Pro Reverb, Twin Super Equivalent to Manufacturer part number 125C1A & 022699 Specifications:
Features:
- Inductance ± 15%: 4 H
- D.C. Current: 90 mA
Features:
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Inductances measured at rated D.C. current.
- Material used & design specs.
$25.98
Choke - Hammond, for Fender Deluxe, Deluxe Reverb, etc.
Replacement for Fender Deluxe, Deluxe Reverb, Vibrolux, Vibrolux Reverb Equivalent to Manufacturer part number 125C3A & 022707 Specifications: Inductance ± 15% 4 H D.C. Current 50 mA Features:
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Inductances measured at rated D.C. current.
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
- Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
$21.95
Choke - Hammond, replacement for Marshall amps
Features:
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Inductances measured at rated D.C. current.
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
- Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
Starting at $27.62
Transformer - Hammond, Low Voltage / Filament, Open, 6.3 VCT
- Open style, chassis mount transformers with a 115V 60Hz or 117 50/60Hz primary and a 6.3V center tapped secondary.
Starting at $13.25
Transformer - Hammond, Tube Output, Push-Pull
- Designed for push-pull tube output circuits.
- Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
- Frequency response 30 Hz. to 30 Khz. at full rated power (± 1 db max. - ref.
Starting at $71.94
Save 37%
Originally: $114.10
Transformer - Hammond, Output, replacement for Marshall
- Replacements for Marshall Amps
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $49.95
Transformer - Audio Interstage, Coil Assembly for P-T156
Coil assembly for P-T156. Use your own iron to preserve mechanical fit. Coil window is 1/2 x ½".
$15.65
Transformer - Output, 8 W, 4kΩ - 9kΩ impedance
Specifications Output 8 W Primary Impedance 4,000 to 9,000 Ω Mounting Centers 2.375" Weight 0.7 lbs
$21.39
Transformer - Power, 120V primary, 140/28/10.5 V secondary
Primary voltage = black wires Secondary 1 = Red wires Secondary 2 = Yellow wires Secondary 3 = Green wires
- Primary Voltage: 120 V
- Secondary 1: 140 V @ 100 mA
- Secondary 2: 28 V @ 20 mA
- Secondary 3: 10.5 V @ 2 A
Primary voltage = black wires Secondary 1 = Red wires Secondary 2 = Yellow wires Secondary 3 = Green wires
$19.95
Transformer - Isolation, 50 VA, 115V, 435 mA, 2 x 115V
An Isolation Power Transformer for isolating equipment from direct connection to the power line. The transformer is constructed with non-concentrically wound coils. The primary and secondary are wound on separate arbors, then assembled on a laminate core side-by-side separated by insulation. This prevents electrical connection, under normal or overload conditions, between the primary and secondary windings.
$22.45
Transformer - Hammond, Universal Push-Pull
- Designed for general purpose or replacement use in push-pull tube output circuits. (For single ended use, see our 125 SE series - optimized for single ended tube output circuits).
- Frequency response: 150 Hz. - 15 Khz (± 1db max. ref. 1 Khz).
- Open style with minimum 5" long primary leads, secondary solder lugs for convenient secondary connections.
- Tables provided with transformer listing 90 pre-calculated impedance ratios.
Starting at $49.95