You are here

Transformers & Chokes

Hammond - Hammond Manufacturing offers a full range of transformers, chokes and enclosures.
Filter these results
Sort By:
products per page
View Mode: List View · Grid View

Pages

(14 pages)
P-T1750X-FENDERTransformer - Hammond, Output, replacement for Fender
  • Replacements for Fender Amps
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

Starting at $18.44
Click to read more
P-T154-P-T156-XFilter Choke - Hammond, Open Bracket

Features



  • Economical "open bracket" - channel mount.
  • Tolerance of 15% on both inductance & resistance.
  • Inductances measured at rated D.C.

Starting at $13.02
Note:
P-T155B: 6 mH / 2 A
P-T154G: 9 H / 40 mA (700 ohm)
P-T155C: 60 H / 8 mA
are special order items.
Note: some of these items are special order items.
Click to read more
P-T290-FENDER-120Transformer - Hammond, Guitar Amplifier, replacement for Fender, 120 V
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
  • See P-T290-FENDER-120-UP for upgraded 120 V transformers, P-T290-FENDER-240 for 240 V transformers


Warning: Not all amplifier models of the same name use the same transformer model.


Starting at $36.25
Click to read more
P-T263-XTransformer - Hammond, High Voltage Plate & Filament, Vertical mount
  • Vertical Mount. For Horizontal Mount, see P-T263-Z
  • Primary 115 VAC, 60 Hz. - except as noted
  • Enclosed, 4 hole, chassis mount.
  • Minimum 6" long leads.
  • Units can be run full wave bridge or full wave C.T.
  • Class A insulation (105 degrees C).
  • Hi-Pot test of 2,000V RMS.
  • Conservative designs - CSA certified (209651).

Starting at $50.06
Click to read more
P-T166-6Transformer - Hammond, Low Voltage / Filament, Open, 6.3 VCT
  • Open style, chassis mount transformers with a 115V 60Hz or 117 50/60Hz primary and a 6.3V center tapped secondary.

Starting at $10.02
Note: P-T166K6: 7.56 is a special order item.
Click to read more
P-T125XSETransformer - Hammond, Universal Single Ended
  • Designed for general purpose or replacement use (not Hi-Fi), in single ended, tube output circuits.
  • Frequency response: 100 Hz. - 15 Khz (± 1db max. - ref. 1 Khz). (For full frequency response (20 Hz. to 20 Khz.) - see P-T1627SE).
  • For push-pull output use, see P-T125A - optimized for push-pull tube output circuits.
  • Open style with minimum 12" long primary & secondary leads leads.
  • All sizes use butt stacked cores (using 29M6 steel) with an air gap, to reduce D.C. core saturation.
  • Primary impedance range from 2,500 to 10,000 Ohms.
  • Secondary impedance range from 4 to 32 Ohms.





Part No.
Audio Power
Max D.C. Bias
Dimensions (Inches)


A
B
C
D
E
G Mtg.
Starting at $45.84
Click to read more
P-T1750X-MARSHALLTransformer - Hammond, Output, replacement for Marshall
  • Replacements for Marshall Amps
  • Designed for drop in replacement of original units.
  • Physically, parts were designed to look similar to original factory units (where possible).
  • Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

Starting at $37.50
Click to read more
P-T261X6Transformer - Hammond, Plate & Filament or Bias, 6.3 V auxiliary
  • Primary 115 VAC, 60 Hz.
  • Designed for small power or bias supplies, test equipment, preamps etc.
  • Models P-T261C6, P-T261E6, and P-T261G6 can also be used with full wave C.T. rectifiers.
  • Economical , two hole, channel bracket, chassis mount.
  • Minimum 5" long leads.
  • Convenient 6.3 filament/auxiliary winding.

Starting at $33.87
Click to read more
P-T125XTransformer - Hammond, Universal Push-Pull
  • Designed for general purpose or replacement use in push-pull tube output circuits. (For single ended use, see our 125 SE series - optimized for single ended tube output circuits).
  • Frequency response: 150 Hz. - 15 Khz (± 1db max. ref. 1 Khz).
  • Open style with minimum 5" long primary leads, secondary solder lugs for convenient secondary connections.
  • Tables provided with transformer listing 90 pre-calculated impedance ratios.

Starting at $36.82
Click to read more
P-T1650XTransformer - Hammond, Tube Output, Push-Pull
  • Designed for push-pull tube output circuits.
  • Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
  • Frequency response 30 Hz. to 30 Khz. at full rated power (± 1 db max. - ref.

Starting at $85.25
Click to read more

Pages

(14 pages)
Don't see a product you're looking for? Send us your product suggestions!
Subscribe to RSS - Transformers & Chokes