Transformer - Hammond, Guitar Amplifier, replacement for Fender, 120 V Designed for drop in replacement of original units. Physically, parts were designed to look similar to original factory units (where possible). Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone". See P-T290-FENDER-120-UP for upgraded 120 V transformers, P-T290-FENDER-240 for 240 V transformers
Warning: Not all amplifier models of the same name use the same transformer model.
Starting at $36.25
Click to read more
Transformer - Hammond, High Voltage Plate & Filament, Vertical mount Vertical Mount. For Horizontal Mount, see P-T263-Z Primary 115 VAC, 60 Hz. - except as noted Enclosed, 4 hole, chassis mount. Minimum 6" long leads. Units can be run full wave bridge or full wave C.T. Class A insulation (105 degrees C). Hi-Pot test of 2,000V RMS. Conservative designs - CSA certified (209651).
Starting at $50.06
Click to read more
Transformer - Hammond, Low Voltage / Filament, Open, 6.3 VCT Open style, chassis mount transformers with a 115V 60Hz or 117 50/60Hz primary and a 6.3V center tapped secondary.
Starting at $10.02
Click to read more
Transformer - Hammond, Plate & Filament or Bias, 6.3 V auxiliary Primary 115 VAC, 60 Hz. Designed for small power or bias supplies, test equipment, preamps etc. Models P-T261C6, P-T261E6, and P-T261G6 can also be used with full wave C.T. rectifiers. Economical , two hole, channel bracket, chassis mount. Minimum 5" long leads. Convenient 6.3 filament/auxiliary winding.
Starting at $33.87
Click to read more
Transformer - Hammond, Guitar Amplifier, replacement for Marshall Replacements for Marshall amps Designed for drop in replacement of original units. Physically, parts were designed to look similar to original factory units (where possible). Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $96.50
Click to read more
Transformer - Hammond, High Voltage Universal Plate & Filament, Vertical mount Primary: Universal - 100, 110, 120, 200, 220,230, 240 VAC 50/60 Hz.
NOTE: units are designed to operate with BOTH primary windings engaged. See primary wiring information under resources. Bias Tap: 50 VAC tap from high voltage secondary C.T. (except part number P-T379WX - uses a separate 60VAC 0.2 Amp winding). Highpot tested: 2,000 VAC Faraday Copper Primary Shield: Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries (shield is internally grounded to the end bell). Windings: Concentric wound for low stray field and low noise. Models: This series is an upgrade from our P-T263-X range of units PLUS 2 models designed specifically for 300B tubes (Part Number P-T300BX) and 2A3 tubes (Part Number P-T302AX). Finish: Black powder paint to match our P-T1650X series of output transformers Units can be run full wave bridge or full wave C.T. Conservative designs - CSA certified (209651).
Starting at $70.22
Click to read more
Transformer - Hammond, Guitar Amplifier, replacement for Fender, 240 V Designed for drop in replacement of original units. Physically, parts were designed to look similar to original factory units (where possible). Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone". See P-T290-FENDER-120 for 120 V transformers, P-T290-Fender-120-UP for upgraded 120 V transformers
Warning: Not all amplifier models of the same name use the same transformer model.
Starting at $41.00
Click to read more
Transformer - Hammond, Low Voltage / Filament, Open, 5 VCT Open style, chassis mount transformers with a 115V 60Hz primary and a 5V center tapped secondary.
Starting at $19.95
Click to read more
Transformer - Hammond, Low Voltage / Filament, Open, 2.5 VCT Open style, chassis mount transformers with a 115V 60Hz primary and a 2.5V center tapped secondary.
Starting at $16.44
Partially Out of Stock
Click to read more
Transformer - Hammond, High Voltage Plate & Filament, Horizontal mount Horizontal mount. For Vertical Mount, see P-T263-X Primary 117 VAC, 50/60 Hz. - except as noted Enclosed, 4 hole, chassis mount. Minimum 6" long leads. Units can be run full wave bridge or full wave C.T. Class A insulation (105 degrees C). Hi-Pot test of 2,000V RMS. Conservative designs - CSA certified (209651). For Vertical Mount, see P-T263-X
Starting at $67.25
Click to read more