Transformers & Chokes

• Primary 115 VAC, 60 Hz.
• Designed for small power or bias supplies, test equipment, preamps etc.
• Models P-T261C6, P-T261E6, and P-T261G6 can also be used with full wave C.T. rectifiers.
• Economical , two hole, channel bracket, chassis mount.
• Minimum 5" long leads.
• Convenient 6.3 filament/auxiliary winding.

An Isolation Power Transformer for isolating equipment from direct connection to the power line. The transformer is constructed with non-concentrically wound coils. The primary and secondary are wound on separate arbors, then assembled on a laminate core side-by-side separated by insulation. This prevents electrical connection, under normal or overload conditions, between the primary and secondary windings.

Specifications Output 8 W Primary Impedance 4,000 to 9,000 Ω Mounting Centers 2.375" Weight 0.7 lbs

• Open style, chassis mount transformers with a 115V 60Hz primary and a 2.5V center tapped secondary.

Fender Original Hot Rod Deluxe Power Transformer. Equivalent to #036958.



Specifications



Primary
120 VAC @ 60 Hz (Black - White)


Secondary 1 (Red - Red)
495 VDC unloaded, 440 VDC @ 65.7 mA DC, 388 VDC @ 200 mA DC


Secondary 2 (Brown - Brown)
53.6 VAC @ 1.58 A AC


Secondary 3 (Green - Green)
6.6 VAC @ 3.75 A AC


Warning: Not all amplifier models of the same name use the same transformer model. Please make sure the amplifier transformer which you are replacing has a Fender number matching the equivalent Fender transformer number listed here.

• Designed for general purpose or replacement use in push-pull tube output circuits. (For single ended use, see our 125 SE series - optimized for single ended tube output circuits).
• Frequency response: 150 Hz. - 15 Khz (± 1db max. ref. 1 Khz).
• Open style with minimum 5" long primary leads, secondary solder lugs for convenient secondary connections.
• Tables provided with transformer listing 90 pre-calculated impedance ratios.

• Designed for drop in replacement of original units. Upgraded units with variable voltage.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
• See P-T290-FENDER-120 for 120 V basic transformers, P-T290-FENDER-240 for 240 V transformers

Warning: Not all amplifier models of the same name use the same transformer model.

Coil assembly for P-T156. Use your own iron to preserve mechanical fit. Coil window is 1/2 x ½".

Includes: 3 pole, 3 position rotary switch (3P3T), 1/4" output jack and black chicken head knob. Hammond 1600A series transformers provide 'easy wire secondary' impedances of 4, 8, or 16 ohms. We now offer a selector switch, pre-wired and complete with 1/4" output jack. Follow simple instructions provided to wire transformer secondary to switch, mount switch and 1/4" jack in separate 3/8" diameter holes in chassis and you'll easily be able to select output impedance as necessary. (Not recommended for 1645A or 1650G)
(See P-H1600 for a selector switch to work with Hammond 1600 series transformers.)

• Enclosed, 4-hole mount chokes
• Tolerance of 15% on both inductance & resistance.
• Inductances measured at rated D.C. current.
• Minimum 8" long leads.
• Units will exhibit less inductance at slightly higher currents or more at lower currents.
• Perfect for high voltage power supply filtering, case matches power transformers & tube audio output transformers.
• Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
• For more sizes and voltages (open - bracket mount type) - see P-T154-P-T156-X
• Operating temperature range is -40C to 85C

• Universal primary with taps for 100, 120, 220 or 240 VAC, 50 / 60 Hz. (Except the 260A6 which is 117V, 50/60 Hz only)
• Designed for preamps, low power amps, general replacement, test equipment, etc.
• Economical, open frame, chassis mount - two hole (.187 dia. = G) channel bracket (figure #1) or four hole mounting (figure #2).
• Units include a Faraday shield between the primary and secondary windings. Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries.
• Minimum 5" long leads.
• For more selection check out our P-T300-X series of universal plate & filament transformers.

Fender Original Hot Rod Deluxe and Blues Deluxe output transformer. 40 watts. Equivalent to #050438.

Specifications Primary 117 V, 50/60 Hz Secondary 125 V, 15 mA Filament Winding 12.6V, 0.3 A Mounting Centers 2" Mounting Type U-bracket Weight 0.7 lbs

• Designed for push-pull tube output circuits.
• Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
• Frequency response 30 Hz. to 30 Khz. at full rated power (± 1 db max. - ref.

• Open style, chassis mount transformers with a 115V 60Hz or 117 50/60Hz primary and a 12.6V center tapped secondary

Replacement for Bassman heads. Equivalent to #125A13A & #022871.

Studio Grade Impedance Matching, 1140 Series. ​Designed with Nickel alloy cores for high performance and Wide Bandwidth. Frequency Response: 20 Hz – 20 kHz ±0.35 dB, (ref. @ 1 kHz). Low distortion at levels up to +27 dBu @ 20 Hz. Open Style

• Open style, chassis mount transformers with a 115V 60Hz primary and a 5V center tapped secondary.

Open frame 6.3V center tapped filament transformer with a 117V 50/60Hz. primary featuring a 100V tap for Japan

• Open Style, Chassis mount
• 117 VAC, 50/60 Hz. with 100V Tap
• Secondary 6.3 C.T.
• Center tapped secondary
• Open style, channel bracket, two hole chassis mount
• Minimum 6" long leads
• Dual bobbin design - no electrostatic shield required
• Class B insulation (130 degrees, C)
• Hi-Pot test of 2,000 V RMS
• CSA certified

Great for upgrading later issue Marshall™ amps. Gives great classic sound.
Good replacement for JMP and JCM 800s. for EL34!

Fender Original Blues Junior Power Transformer. Equivalent to #049967.

Dual 117/234 VAC primary, 50/60 Hz. operation. 220 V series, 110 V parallel secondary.

Dual 117/234 VAC primary, 50/60 Hz. operation. 24 V series, 12 V parallel secondary.

Open style, chassis mount transformers with a 115V 60Hz primary and a 12V center tapped secondary.