Transformers & Chokes
Transformer - Hammond, Filament High Current, 115V, 60V/5A, 300VA
Low Voltage, Filament High Current, Chassis Mount. 115 V primary.
$107.32
Transformer - Fender, Power, for Deluxe Reverb 120V
Genuine Fender power transformer designed for use in the ‘65 Deluxe Reverb as well as the ‘68 Deluxe. Made to original fender specifications. 120V Primary
$105.95
Transformer - Hammond, Guitar Amplifier, replacement for Ampeg
Part No.
Primary
Ampeg Model Names
Ampeg Part No
Bobbin/Paper Wound
VAC
Hz.
P-T291GX
120 V
60 Hz.
B25
12XA
Bobbin
P-T290CAZ
117 V
60 Hz.
Gemini VI 25W
PT 113
Bobbin
P-T290ETX
120 V
60 Hz.
Super Echo Twin
PT 109
Bobbin
P-T291HX
110 / 115 / 230 V
50 / 60 Hz.
V50H
94-270-030
Bobbin
- Replacement for Ampeg amplifiers
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Part No.
Primary
Ampeg Model Names
Ampeg Part No
Bobbin/Paper Wound
VAC
Hz.
P-T291GX
120 V
60 Hz.
B25
12XA
Bobbin
P-T290CAZ
117 V
60 Hz.
Gemini VI 25W
PT 113
Bobbin
P-T290ETX
120 V
60 Hz.
Super Echo Twin
PT 109
Bobbin
P-T291HX
110 / 115 / 230 V
50 / 60 Hz.
V50H
94-270-030
Bobbin
Starting at $105.82
Transformer - Fender®, Output, 50 W, 2 Ω
Fender® Original '59 Bassman Reissue output transformer. Equivalent to #036485.
$99.95
Transformer - Fender®, Power, Hot Rod Deville
Fender Original Hot Rod DeVille Power Transformer. Equivalent to #041752.
$99.95
Transformer - Hammond, High Voltage Universal Plate & Filament, Vertical mount
- Primary: Universal - 100, 110, 120, 200, 220,230, 240 VAC 50/60 Hz.
- NOTE: units are designed to operate with BOTH primary windings engaged.
- See primary wiring information under resources.
- Bias Tap: 50 VAC tap from high voltage secondary C.T. (except part number P-T379WX - uses a separate 60VAC 0.2 Amp winding).
- Highpot tested: 2,000 VAC
- Faraday Copper Primary Shield: Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries (shield is internally grounded to the end bell).
- Windings: Concentric wound for low stray field and low noise.
- Models: This series is an upgrade from our P-T263-X range of units PLUS 2 models designed specifically for 300B tubes (Part Number P-T300BX) and 2A3 tubes (Part Number P-T302AX).
- Finish: Black powder paint to match our P-T1650X series of output transformers Units can be run full wave bridge or full wave C.T.
- Conservative designs - CSA certified (209651).
Starting at $98.67
Transformer - Hammond, Toroidal Power, 90V / 180V secondary
Dual 117/234 VAC primary, 50/60 Hz. operation. 180 V series, 90 V parallel secondary.dary.
$97.65
Transformer - Hammond, Power, 250-0-250 V, 100 mA
Primary 115 VAC 60 Hz.
Secondary DC current measured with cap. input filter, full wave (two diode) C.T., rectifier circuit.
Enclosed, 4 hole chassis mount.
Minimum 6 long leads.
2" X 2" vertical mounting centers.
Class A insulation (105 degrees C).
Hi-Pot test of 2000 V RMS.
Conservative designs - CSA certified (# LR3902).
3.2lbs
Secondary: 250-0-250 V100 mA
Filament winding 1: 5 V2 A
Filament winding 2: 6.3 V3 A
Secondary DC current measured with cap. input filter, full wave (two diode) C.T., rectifier circuit.
Enclosed, 4 hole chassis mount.
Minimum 6 long leads.
2" X 2" vertical mounting centers.
Class A insulation (105 degrees C).
Hi-Pot test of 2000 V RMS.
Conservative designs - CSA certified (# LR3902).
3.2lbs
Secondary: 250-0-250 V100 mA
Filament winding 1: 5 V2 A
Filament winding 2: 6.3 V3 A
$92.63
Transformer - Hammond, Microphone Input Transformers
Studio Grade Impedance Matching, 1140 Series. Designed with Nickel alloy cores for high performance and Wide Bandwidth. Frequency Response: 20 Hz – 20 kHz ±0.35 dB, (ref. @ 1 kHz). Low distortion at levels up to +27 dBu @ 20 Hz. Excellent Shielding – Mu Metal enclosures
Starting at $91.97
Transformer - Hammond, Direct Box Transformer
Studio Grade Impedance Matching, 1140 Series. Designed with Nickel alloy cores for high performance and Wide Bandwidth. Frequency Response: 20 Hz – 20 kHz ±0.35 dB, (ref. @ 1 kHz). Low distortion at levels up to +27 dBu @ 20 Hz. Excellent Shielding – Mu Metal enclosures
$91.68
Transformer - Hammond, Output, replacement for Vox
- Replacements for Vox Amps
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $91.00
Save 23%
Originally: $118.72
Transformer - Power, 120V Primary, 330V / 6.3VCT / 5V Secondary, for Fender® Deluxe 5E3
Power transformer replacement for the Fender® part number 64526 as used in the 5E3 Deluxe Amp. This transformer accounts for modern mains voltage and will provide a B+ voltage of ~370VDC with 120VAC on the primary in a standard 5E3 build paired with the P-TGO-002 output transformer. This upgraded transformer also features a center tap on the 6.3V filament. Features
- Provides vintage correct DC voltages in stock 5E3 builds
- 330V (660 VCT) B+ at 120mA
- Center tapped 6.3V filament at 2A
- 5V filament supply at 2A
- For 120V 60Hz primary
- Standard 2.8125" x 2.25” mounting centers
$89.95
Transformer - Hammond, High Voltage Plate & Filament, Horizontal mount
- Horizontal mount. For Vertical Mount, see P-T263-X
- Primary 117 VAC, 50/60 Hz. - except as noted
- Enclosed, 4 hole, chassis mount.
- Minimum 6" long leads.
- Units can be run full wave bridge or full wave C.T.
- Class A insulation (105 degrees C).
- Hi-Pot test of 2,000V RMS.
- Conservative designs - CSA certified (209651).
- For Vertical Mount, see P-T263-X
Starting at $88.07
Save 7%
Originally: $95.10
Transformer - Fender®, Power, Blues Junior, 15 W
Fender Original Blues Junior Power Transformer. Equivalent to #049967.
$87.95
Transformer - Hammond, Isolation, 100VA
Capacity: 100 VA
Features:
Features:
- Primary 115VAC, 60 Hz.
- Secondary taps @ 90, 100, 110, 115, 120 & 130VAC
- Electrostatic shield between primary & secondary
- Connection by flexible leads, 8" minimum length
- Perfect for critical line voltage needs (examples: older "classic" tube equipment or Japanese 100V equipment).
- CSA certified (# LR3902)
- Remember - These units do NOT convert line frequency
$84.95
Transformer - Hammond, Line Input Transformers
Studio Grade Impedance Matching, 1140 Series. Designed with Nickel alloy cores for high performance and Wide Bandwidth. Frequency Response: 20 Hz – 20 kHz ±0.35 dB, (ref. @ 1 kHz). Low distortion at levels up to +27 dBu @ 20 Hz. Excellent Shielding – Mu Metal enclosures
Starting at $83.63
Transformer - Hammond, Studio Grade Impedance Matching, 140 Series
Studio grade frequency response: 20 Hz. - 20 Khz. (+/- 1 db, ref. @ 1 Khz.) minimum. Excellent frequency response utilizing a 80% nickel core providing high permeability combined with low losses. Designed for maximum bandwidth, lowest distortion at +10 dbm power level or less. Plated steel cans, adjustable height case bracket.
Starting at $82.70
Transformer - Hammond, Output, replacement for Orange Rocker 30
Hammond output transformer - replacement for Orange Rocker 30 Specifications: Part No. Pri Ohms Sec Ohms Amplifier Type Watts Bobbin/Paper Winding Equivalent To P-T1750ORF 6,000 C.T. 8, 16 Push-Pull 35 W Bobbin OT199SL
$82.23
Transformer - Hammond, Plate & Filament
- Universal primary with taps for 100, 120, 220 or 240 VAC, 50 / 60 Hz. (Except the 260A6 which is 117V, 50/60 Hz only)
- Designed for preamps, low power amps, general replacement, test equipment, etc.
- Economical, open frame, chassis mount - two hole (.187 dia. = G) channel bracket (figure #1) or four hole mounting (figure #2).
- Units include a Faraday shield between the primary and secondary windings. Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries.
- Minimum 5" long leads.
- For more selection check out our P-T300-X series of universal plate & filament transformers.
Starting at $81.68
Transformer - Fender®, Power, for '65 Twin Reverb Reissue
Made precisely to the original Fender® specifications. Drop-in replacement for '65 Twin Reverb Reissue. Made in the USA. 120V Primary.
$79.95
Transformer - Hammond, Low Voltage / Filament, Open, 72 VCT
Open style, chassis mount transformers with a 117V 50/60Hz primary and a 72V center tapped secondary.
$79.07
Transformer - Hammond, Isolation, 115V
- Primary 115VAC, 60 Hz.
- Secondary 115VAC
- Electrostatic shield between primary & secondary
- Connection by flexible leads, 8" minimum length
- Perfect for circuit isolation or "Classic" bias power supply
- CSA certified (209651)
- Remember - These units do NOT convert line frequency
Starting at $76.73
Transformer - Hammond, Low Voltage / Filament, Enclosed, 60 VCT
- Primary 115 VAC, 60 Hz.
- Secondary 60 C.T.
- All secondaries center tapped, VAC (RMS)
- Enclosed, 4 hole chassis mount.
- Minimum 6" long leads.
- Dual bobbin design - no electrostatic shield required.
- Class B insulation (130 degrees C).
- Hi-Pot test of 2,000V RMS.
- UL listed (# E50394) & CSA certified (209651).
$76.40
Transformer - Hammond, Microphone Splitter Transformers
Studio Grade Impedance Matching, 1140 Series. Designed with Nickel alloy cores for high performance and Wide Bandwidth. Frequency Response: 20 Hz – 20 kHz ±0.35 dB, (ref. @ 1 kHz). Low distortion at levels up to +27 dBu @ 20 Hz. Excellent Shielding – Mu Metal enclosures
Starting at $75.35