Transformers & Chokes
Transformer - Hammond, High Voltage Universal Plate & Filament, Vertical mount
- Primary: Universal - 100, 110, 120, 200, 220,230, 240 VAC 50/60 Hz.
- NOTE: units are designed to operate with BOTH primary windings engaged.
- See primary wiring information under resources.
- Bias Tap: 50 VAC tap from high voltage secondary C.T. (except part number P-T379WX - uses a separate 60VAC 0.2 Amp winding).
- Highpot tested: 2,000 VAC
- Faraday Copper Primary Shield: Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries (shield is internally grounded to the end bell).
- Windings: Concentric wound for low stray field and low noise.
- Models: This series is an upgrade from our P-T263-X range of units PLUS 2 models designed specifically for 300B tubes (Part Number P-T300BX) and 2A3 tubes (Part Number P-T302AX).
- Finish: Black powder paint to match our P-T1650X series of output transformers Units can be run full wave bridge or full wave C.T.
- Conservative designs - CSA certified (209651).
Starting at $90.06
Save 9%
Originally: $98.67
Transformer - Hammond, Guitar Amplifier, replacement for Marshall
- Replacements for Marshall amps
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $128.95
Transformer - Hammond, Plate & Filament or Bias, 6.3 V auxiliary
- Primary 115 VAC, 60 Hz.
- Designed for small power or bias supplies, test equipment, preamps etc.
- Models P-T261C6, P-T261E6, and P-T261G6 can also be used with full wave C.T. rectifiers.
- Economical , two hole, channel bracket, chassis mount.
- Minimum 5" long leads.
- Convenient 6.3 filament/auxiliary winding.
Starting at $40.25
Transformer - Fender®, Output, Hot Rod Deluxe and Blues Deluxe
Fender Original Hot Rod Deluxe and Blues Deluxe output transformer. 40 watts. Equivalent to #050438.
$59.95
Transformer - Hammond, Universal Push-Pull
- Designed for general purpose or replacement use in push-pull tube output circuits. (For single ended use, see our 125 SE series - optimized for single ended tube output circuits).
- Frequency response: 150 Hz. - 15 Khz (± 1db max. ref. 1 Khz).
- Open style with minimum 5" long primary leads, secondary solder lugs for convenient secondary connections.
- Tables provided with transformer listing 90 pre-calculated impedance ratios.
Starting at $49.95
Transformer - Output, 15W, 8kΩ CT Primary, for Fender® Deluxe 5E3
Paper bobbin output transformer replacement for the Fender® part number 50246 as used in the 5E3 Deluxe Amp. This transformer has an 8kΩ center tapped primary and an 8Ω secondary. Features
- Paper Bobbin
- Vintage Style Color Code
- 8kΩ Center Tapped Primary
- 8Ω Secondary
- Standard 3.125” Mounting Centers
$29.95
Filter Choke - Hammond, D.C. choke, Enclosed
- Enclosed, 4-hole mount chokes
- Tolerance of 15% on both inductance & resistance.
- Inductances measured at rated D.C. current.
- Minimum 8" long leads.
- Units will exhibit less inductance at slightly higher currents or more at lower currents.
- Perfect for high voltage power supply filtering, case matches power transformers & tube audio output transformers.
- Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
- For more sizes and voltages (open - bracket mount type) - see P-T154-P-T156-X
- Operating temperature range is -40C to 85C
Starting at $47.57
Save 10%
Originally: $52.95
Transformer - Hammond, Tube Output, Push-Pull
- Designed for push-pull tube output circuits.
- Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
- Frequency response 30 Hz. to 30 Khz. at full rated power (± 1 db max. - ref.
Starting at $119.80
Transformer - Hammond, Tube Output, Easy Wire Secondary
- Designed for push-pull tube output circuits.
- Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
- Frequency response 30 Hz. to 30 Khz. at full rated power (± 1 db max. - ref.
Starting at $135.63
Transformer - Hammond, Low Voltage / Filament, Open, 12 VCT
Open style, chassis mount transformers with a 115V 60Hz primary and a 12V center tapped secondary.
Starting at $11.62
Transformer - Fender®, Reverb, for Pro Reverb
Original Fender® reverb driver for Pro Reverb. Replacement for #037099. Warning: Not all amplifier models of the same name use the same transformer model. Please make sure the amplifier transformer which you are replacing has a Fender number matching the equivalent Fender transformer number listed here.
See P-TGR-001 for a generic Fender® style reverb driver.
See P-TGR-001 for a generic Fender® style reverb driver.
$28.95
Transformer - Fender®, Power, Hot Rod Deluxe
Fender Original Hot Rod Deluxe Power Transformer. Equivalent to #036958.
Specifications
Primary
120 VAC @ 60 Hz (Black - White)
Secondary 1 (Red - Red)
495 VDC unloaded, 440 VDC @ 65.7 mA DC, 388 VDC @ 200 mA DC
Secondary 2 (Brown - Brown)
53.6 VAC @ 1.58 A AC
Secondary 3 (Green - Green)
6.6 VAC @ 3.75 A AC
Warning: Not all amplifier models of the same name use the same transformer model. Please make sure the amplifier transformer which you are replacing has a Fender number matching the equivalent Fender transformer number listed here.
Specifications
Primary
120 VAC @ 60 Hz (Black - White)
Secondary 1 (Red - Red)
495 VDC unloaded, 440 VDC @ 65.7 mA DC, 388 VDC @ 200 mA DC
Secondary 2 (Brown - Brown)
53.6 VAC @ 1.58 A AC
Secondary 3 (Green - Green)
6.6 VAC @ 3.75 A AC
Warning: Not all amplifier models of the same name use the same transformer model. Please make sure the amplifier transformer which you are replacing has a Fender number matching the equivalent Fender transformer number listed here.
$145.95
Transformer - Hammond, Low Voltage / Filament, Open, 12.6 VCT
- Open style, chassis mount transformers with a 115V 60Hz or 117 50/60Hz primary and a 12.6V center tapped secondary
Starting at $13.95
Transformer - Fender®, Power, Blues Junior, 15 W
Fender Original Blues Junior Power Transformer. Equivalent to #049967.
$87.95
Transformer - Marshall Replacement, Output, 100 W
Great for upgrading later issue Marshall™ amps. Gives great classic sound.
Good replacement for JMP and JCM 800s. for EL34!
Good replacement for JMP and JCM 800s. for EL34!
$143.95
Switch - Rotary Impedance Selector, for Hammond 1600A series
Includes: 3 pole, 3 position rotary switch (3P3T), 1/4" output jack and black chicken head knob. Hammond 1600A series transformers provide 'easy wire secondary' impedances of 4, 8, or 16 ohms. We now offer a selector switch, pre-wired and complete with 1/4" output jack. Follow simple instructions provided to wire transformer secondary to switch, mount switch and 1/4" jack in separate 3/8" diameter holes in chassis and you'll easily be able to select output impedance as necessary. (Not recommended for 1645A or 1650G)
(See P-H1600 for a selector switch to work with Hammond 1600 series transformers.)
(See P-H1600 for a selector switch to work with Hammond 1600 series transformers.)
$11.95
Transformer - Power, 120V Primary, 330V / 6.3VCT / 5V Secondary, for Fender® Deluxe 5E3
Power transformer replacement for the Fender® part number 64526 as used in the 5E3 Deluxe Amp. This transformer accounts for modern mains voltage and will provide a B+ voltage of ~370VDC with 120VAC on the primary in a standard 5E3 build paired with the P-TGO-002 output transformer. This upgraded transformer also features a center tap on the 6.3V filament. Features
- Provides vintage correct DC voltages in stock 5E3 builds
- 330V (660 VCT) B+ at 120mA
- Center tapped 6.3V filament at 2A
- 5V filament supply at 2A
- For 120V 60Hz primary
- Standard 2.8125" x 2.25” mounting centers
$89.95
Transformer - Hammond, Low Voltage / Filament, Open, 2.5 VCT
- Open style, chassis mount transformers with a 115V 60Hz primary and a 2.5V center tapped secondary.
Starting at $19.85
Transformer - Fender, Power, for Deluxe Reverb 120V
Genuine Fender power transformer designed for use in the ‘65 Deluxe Reverb as well as the ‘68 Deluxe. Made to original fender specifications. 120V Primary
$105.95
Transformer - Fender® Replacement, Output, 50 W, 4 Ohm
Replacement for Bassman heads. Equivalent to #125A13A & #022871.
$53.58
Save 23%
Originally: $69.95
Transformer - Hammond, Low Voltage / Filament, Open, 5 VCT
- Open style, chassis mount transformers with a 115V 60Hz primary and a 5V center tapped secondary.
Starting at $26.35
Transformer - Marshall, Output, 100 W, for JCM900
Genuine Marshall™ 100 watt output transformer for JCM900 and JCM2000.
For a Hammond option, see P-T1750P.
For a Hammond option, see P-T1750P.
$139.95
Out of Stock
Transformer - Hammond, Plate & Filament
- Universal primary with taps for 100, 120, 220 or 240 VAC, 50 / 60 Hz. (Except the 260A6 which is 117V, 50/60 Hz only)
- Designed for preamps, low power amps, general replacement, test equipment, etc.
- Economical, open frame, chassis mount - two hole (.187 dia. = G) channel bracket (figure #1) or four hole mounting (figure #2).
- Units include a Faraday shield between the primary and secondary windings. Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries.
- Minimum 5" long leads.
- For more selection check out our P-T300-X series of universal plate & filament transformers.
Starting at $81.68
Transformer - Hammond, Guitar Amplifier, replacement for Vox
- Replacement for Vox amplifiers
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
Starting at $110.80