 | Transformer - Fender® Replacement, Output, 50 W, 4 OhmReplacement for Bassman heads. Equivalent to #125A13A & #022871.
| $69.95 | Click to read more |
 | Transformer - Marshall, Output, for JTM45Genuine Marshall™ output transformer for JTM45.
| $135.00 | Click to read more |
 | Transformer - Marshall, Output, 100 W, for JCM900Genuine Marshall™ 100 watt output transformer for JCM900 and JCM2000.
| $139.95 | Click to read more |
 | Choke - Hammond, replacement for Marshall Plexi JCM800Replacement for Marshall Plexi JCM 800.
Specifications:
- Inductance ± 15%: 40 H
- D.C. Current: 50 mA
Features:
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Inductances measured at rated D.C. current.
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
- Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
| $35.12 | Click to read more |
 | Transformer - Hammond, Low Voltage / Filament, Enclosed, 5 VCTSpecial Order Item
- Primary 115 VAC, 60 Hz.
- Secondary 5 C.T.
- All secondaries center tapped, VAC (RMS)
- Enclosed, 4 hole chassis mount.
- Minimum 6" long leads.
- Dual bobbin design - no electrostatic shield required.
- Class B insulation (130 degrees C).
- Hi-Pot test of 2,000V RMS.
- UL listed (# E50394) & CSA certified (209651).
| Starting at $36.92 | Click to read more |
 | Choke - One Electron, Audio, PRC-2, for Shunt Feed SE OutputThe PRC-2 audio choke from One Electron was designed for shunt-feed single-ended output applications, but is also useful where quality inductive loads are needed or as high-quality filter chokes.
| $69.95 | Click to read more |
 | Transformer - Hammond, Tube Output, Easy Wire Secondary- Designed for push-pull tube output circuits.
- Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
- Frequency response 30 Hz. to 30 Khz. at full rated power (± 1 db max. - ref.
| Starting at $112.58 | Click to read more |
 | Transformer - Hammond, Guitar Amplifier, replacement for Vox- Replacement for Vox amplifiers
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
| Starting at $96.65 | Click to read more |
 | Transformer - Hammond, High Voltage Universal Plate & Filament, Vertical mount- Primary: Universal - 100, 110, 120, 200, 220,230, 240 VAC 50/60 Hz.
- NOTE: units are designed to operate with BOTH primary windings engaged.
- See primary wiring information under resources.
- Bias Tap: 50 VAC tap from high voltage secondary C.T. (except part number P-T379WX - uses a separate 60VAC 0.2 Amp winding).
- Highpot tested: 2,000 VAC
- Faraday Copper Primary Shield: Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries (shield is internally grounded to the end bell).
- Windings: Concentric wound for low stray field and low noise.
- Models: This series is an upgrade from our P-T263-X range of units PLUS 2 models designed specifically for 300B tubes (Part Number P-T300BX) and 2A3 tubes (Part Number P-T302AX).
- Finish: Black powder paint to match our P-T1650X series of output transformers Units can be run full wave bridge or full wave C.T.
- Conservative designs - CSA certified (209651).
| Starting at $82.95 | Click to read more |
 | Transformer - Fender®, Power, Hot Rod DevilleFender Original Hot Rod DeVille Power Transformer. Equivalent to #041752.
| $94.95 | Click to read more |
480.820.5411