 | Audio Transformer - Hammond, 150/600Ω, Line IsolationSpecial Order Item
- 150/600 Ohm Primary Impedance
- 300/1200 Ohm Secondary Impedance
- Deep-drawn steel case with tin plated finish, with two convenient 6-32 mounting studs with mounting hardware.
- Sealed case and wax potted core internally for stable characteristics and long life.
- Wide frequency response ± 0.5 db max. from 20 Hz. to 20 Khz. (except units over 5K ohms impedance, may be down 1 db @ 20 Khz.)
- Insertion loss of apx. 1 db.
- Maximum power level +15 dbm. with specified characteristics, or higher levels with reduced low frequency performance.
- Distortion is apx. 1.5% @ 20 Hz. under full power.
- Electrostatic shield between pri. & sec. connected to the green lead.
- Humbucking construction
- Balanced split windings on pri. & sec. for circuit versatility. Primary may be used as a secondary and vice versa for impedance matching.
- Lead length: Min. 4"
| $146.22 $131.60 You save: 10% | Click to read more |
| Audio Transformer - Hammond, 30W, 3.5kΩ, 42H, Tube OutputSpecial Order Item
- "Over designed" for high fidelity, single ended, Class-A, tube output circuits (triode, tetrode or pentode tubes).
- Enclosed (shielded), four slot, chassis Type "X" mounting.
- Frequency response at least 20 Hz. to 20 Khz. at full rated power (+/- 1 db max., ref. 1 Khz.)
- Insulated flexible leads 8" min.
- For maximum versatility, all units include a 40% screen tap for Ultra-Linear, tetrode/pentode operation (if desired).
- High quality laminations, (M6) grain oriented silicon steel.
- Core is gapped to reduce core saturation in Class-A tube amplifier circuits.
| $193.01 $173.71 You save: 10% | Click to read more |
| Audio Transformer - Hammond, 60W, 6.6kΩ, Push-Pull Tube OutputSpecial Order Item
- Designed for push-pull tube output circuits.
- Units are designed to provide ample "headroom" at bass frequencies
- Has a secondary tap for 4, 8 or 16 ohm outputs.
- Enclosed (shielded), 4 slot, above chassis Type "X" mounting.
- Manufactured with plastic coil forms for coil support and insulation.
- Frequency response 30 Hz. to 30 Khz. at full rated power (+/- 1 db max. - ref. 1 Khz) minimum.
- Insulated flexible leads 8" min.
- Includes 40% screen taps for Ultra-Linear operation (if desired).
- Typical applications - Push-Pull: triode, Ultra-Linear pentode, pentode and tetrode connected audio output.
| $181.31 $163.18 You save: 10% | Click to read more |
 | Choke - 0.17 - 250, Heavy Duty Hash Choke Molded powdered iron core.
1-1/4 long axial leads.
High inductance & high current.
L measured at 1 Khz. Inductance: 250 µH20% tolerance
DC resistance ohms: .17
Self Resonant Frequency (MHz): 1.5
Maximum DC current amps: 2.5
Coil diameter (in): .43
Core Length (in): 1.25 | $1.15 $1.04 You save: 10% | Click to read more |
 | Choke - Hammond, for Fender Bandmaster, Dual Showman, etc.Replacement for Fender Bandmaster, Dual Showman, Pro Reverb, Twin Super Equivalent to Manufacturer part number 125C1A & 022699 Specifications:
- Inductance ± 15%: 4 H
- D.C. Current: 90 mA
Features:
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Inductances measured at rated D.C. current.
- Material used & design specs.
| $18.97 $17.07 You save: 10% | Click to read more |
 | Choke - Hammond, for Fender Deluxe, Deluxe Reverb, etc.Replacement for Fender Deluxe, Deluxe Reverb, Vibrolux, Vibrolux Reverb Equivalent to Manufacturer part number 125C3A & 022707 Specifications:
- Inductance ± 15%: 4 H
- D.C. Current: 50 mA
Features:
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Inductances measured at rated D.C. current.
- Material used & design specs.
| $17.44 $15.70 You save: 10% | Click to read more |
 | Choke - Hammond, Replacement for Marshall PlexiReplacement for Marshall Plexi Specifications:
- Inductance ± 15%: 3 H
- D.C. Current: 250 mA
Features:
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Inductances measured at rated D.C. current.
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
- Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
| $23.51 $21.16 You save: 10% | Click to read more |
 | Choke - Hammond, replacement for Marshall Plexi JCM800Replacement for Marshall Plexi JCM 800.
Specifications:
- Inductance ± 15%: 40 H
- D.C. Current: 50 mA
Features:
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Inductances measured at rated D.C. current.
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
- Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
| $37.28 $33.55 You save: 10% | Click to read more |
 | Choke - Hammond, Replacement for Vox AC30 reissueReplacement for Vox AC30 reissue
Specifications:
- Inductance ± 15%: 5 H
- D.C. Current: 150 mA
Features:
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Inductances measured at rated D.C. current.
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
- Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
| $37.94 $34.15 You save: 10% | Click to read more |
 | Choke - Hammond, Replacement for Vox AC30 vintageReplacement for Vox AC30 vintage
Specifications:
- Inductance ± 15%: 30 H
- D.C. Current: 100 mA
Features:
- Designed for drop in replacement of original units.
- Physically, parts were designed to look similar to original factory units (where possible).
- Inductances measured at rated D.C. current.
- Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
- Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
| $34.64 $31.18 You save: 10% | Click to read more |
480.820.5411