Transformers & Chokes

• Replacements for Fender Amps
• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
• See P-T290-FENDER-120-UP for upgraded 120 V transformers, P-T290-FENDER-240 for 240 V transformers

Warning: Not all amplifier models of the same name use the same transformer model.

Features

• Economical "open bracket" - channel mount.
• Tolerance of 15% on both inductance & resistance.
• Inductances measured at rated D.C.

• Vertical Mount. For Horizontal Mount, see P-T263-Z
• Primary 115 VAC, 60 Hz. - except as noted
• Enclosed, 4 hole, chassis mount.
• Minimum 6" long leads.
• Units can be run full wave bridge or full wave C.T.
• Class A insulation (105 degrees C).
• Hi-Pot test of 2,000V RMS.
• Conservative designs - CSA certified (209651).

Replacement for Fender Bandmaster, Dual Showman, Pro Reverb, Twin Super Equivalent to Manufacturer part number 125C1A & 022699 Specifications:

• Inductance ± 15%: 4 H
• D.C. Current: 90 mA

Features:

• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Inductances measured at rated D.C. current.
• Material used & design specs.

Equivalent to Stancor A53-C. 1:3 ratio overall. Center tapped secondary may be used for push-pull grids.Specifications Max. Primary Current: 10 mA Impedance Primary to Secondary (Ohms): 10,000 to 90,000

Replacement for Fender Deluxe, Deluxe Reverb, Vibrolux, Vibrolux Reverb Equivalent to Manufacturer part number 125C3A & 022707 Specifications: Inductance ± 15% 4 H D.C. Current 50 mA Features:

• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Inductances measured at rated D.C. current.
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
• Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.

Original Fender® reverb driver for Pro Reverb. Replacement for #037099. Warning: Not all amplifier models of the same name use the same transformer model. Please make sure the amplifier transformer which you are replacing has a Fender number matching the equivalent Fender transformer number listed here.

Features:

• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Inductances measured at rated D.C. current.
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".
• Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.

• Primary: Universal - 100, 110, 120, 200, 220,230, 240 VAC 50/60 Hz.
  
  • NOTE: units are designed to operate with BOTH primary windings engaged.
  • See primary wiring information under resources.
• Bias Tap: 50 VAC tap from high voltage secondary C.T. (except part number P-T379WX - uses a separate 60VAC 0.2 Amp winding).
• Highpot tested: 2,000 VAC
• Faraday Copper Primary Shield: Our electrostatic shield reduces the capacitive coupling from the primary - greatly attenuating higher frequency current coupling to the secondaries (shield is internally grounded to the end bell).
• Windings: Concentric wound for low stray field and low noise.
• Models: This series is an upgrade from our P-T263-X range of units PLUS 2 models designed specifically for 300B tubes (Part Number P-T300BX) and 2A3 tubes (Part Number P-T302AX).
• Finish: Black powder paint to match our P-T1650X series of output transformers Units can be run full wave bridge or full wave C.T.
• Conservative designs - CSA certified (209651).

• Designed for general purpose or replacement use (not Hi-Fi), in single ended, tube output circuits.
• Frequency response: 100 Hz. - 15 Khz (± 1db max. - ref. 1 Khz). (For full frequency response (20 Hz. to 20 Khz.) - see P-T1627SE).
• For push-pull output use, see P-T125A - optimized for push-pull tube output circuits.
• Open style with minimum 12" long primary & secondary leads leads.
• All sizes use butt stacked cores (using 29M6 steel) with an air gap, to reduce D.C. core saturation.
• Primary impedance range from 2,500 to 10,000 Ohms.
• Secondary impedance range from 4 to 32 Ohms.

Part No.
Audio Power
Max D.C. Bias
Dimensions (Inches)


A
B
C
D
E
G Mtg.

• Designed for push-pull tube output circuits.
• Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
• Frequency response 30 Hz. to 30 Khz. at full rated power (± 1 db max. - ref.

• Primary 115 VAC, 60 Hz.
• Designed for small power or bias supplies, test equipment, preamps etc.
• Models P-T261C6, P-T261E6, and P-T261G6 can also be used with full wave C.T. rectifiers.
• Economical , two hole, channel bracket, chassis mount.
• Minimum 5" long leads.
• Convenient 6.3 filament/auxiliary winding.

• Open style, chassis mount transformers with a 115V 60Hz or 117 50/60Hz primary and a 6.3V center tapped secondary.

• Replacements for Marshall Amps
• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

• Replacements for Marshall amps
• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

• Designed for general purpose or replacement use in push-pull tube output circuits. (For single ended use, see our 125 SE series - optimized for single ended tube output circuits).
• Frequency response: 150 Hz. - 15 Khz (± 1db max. ref. 1 Khz).
• Open style with minimum 5" long primary leads, secondary solder lugs for convenient secondary connections.
• Tables provided with transformer listing 90 pre-calculated impedance ratios.

Fender Original Hot Rod Deluxe and Blues Deluxe output transformer. 40 watts. Equivalent to #050438.

Coil assembly for P-T156. Use your own iron to preserve mechanical fit. Coil window is 1/2 x ½".

Specifications Output 8 W Primary Impedance 4,000 to 9,000 Ω Mounting Centers 2.375" Weight 0.7 lbs

An Isolation Power Transformer for isolating equipment from direct connection to the power line. The transformer is constructed with non-concentrically wound coils. The primary and secondary are wound on separate arbors, then assembled on a laminate core side-by-side separated by insulation. This prevents electrical connection, under normal or overload conditions, between the primary and secondary windings.

• Enclosed, 4-hole mount chokes
• Tolerance of 15% on both inductance & resistance.
• Inductances measured at rated D.C. current.
• Minimum 8" long leads.
• Units will exhibit less inductance at slightly higher currents or more at lower currents.
• Perfect for high voltage power supply filtering, case matches power transformers & tube audio output transformers.
• Units are vacuum impregnated with polyurethane varnish for quiet and long life operation.
• For more sizes and voltages (open - bracket mount type) - see P-T154-P-T156-X
• Operating temperature range is -40C to 85C

• Designed for push-pull tube output circuits.
• Enclosed (shielded), 4 slot, above chassis Type 'X' mounting.
• Frequency response 30 Hz. to 30 Khz. at full rated power (± 1 db max. - ref.

Great for upgrading later issue Marshall™ amps. Gives great classic sound.
Good replacement for JMP and JCM 800s. for EL34!