Transformers & Chokes

• Replacements for Fender Amps
• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

Low profile mounting, dual - split bobbin design. 12VA.

• Replacements for Yorkville/Traynor Amps
• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

• Open style, chassis mount transformers with a 115V 60Hz primary and a 60V center tapped secondary.

Open style, chassis mount transformers with a 117V 50/60Hz primary and a 48V center tapped secondary.

Genuine Marshall™ 100 watt output transformer for JCM900 and JCM2000.

The PRC-1 audio choke from One Electron was designed for shunt-feed single-ended output applications, but is also useful where quality inductive loads are needed or as high-quality filter chokes.

• Primary 115 VAC, 60 Hz.
• Secondary 6.3 C.T.
• All secondaries center tapped, VAC (RMS)
• Enclosed, 4 hole chassis mount.
• Minimum 6" long leads.
• Dual bobbin design - no electrostatic shield required.
• Class B insulation (130 degrees C).
• Hi-Pot test of 2,000V RMS.
• UL listed (# E50394) & CSA certified (209651).

Dual 117/234 VAC primary, 50/60 Hz. operation. 12 V series, 6 V parallel secondary.mary, 50/60 Hz. operation.

Replacement for Bassman heads. Equivalent to #125A13A & #022871.

Specifications:

• Size: 14 VA
• Dual Primary: 117 VAC, 234VAC, 50/60 Hz.
• Secondary VAC RMS Series: 14V @ 1 A
• Secondary VAC RMS Parallel: 7V @ 2 A

Features:

• Primary 117/234 VAC, 50/60 Hz.
• Dual secondaries
• Secondaries can be used as; a center tapped secondary, parallel connected or used individually
• Units are designed for use with all windings engaged.
• Open style.
• Minimum 6" long leads.
• Dual bobbin design - no electrostatic shield required.
• Class B insulation (130 degrees, C) for extra pr

Open style, chassis mount transformers with a 115V 60Hz primary and an 8V or 8.5V secondary.

Genuine Fender power transformer designed for use in the ‘65 Deluxe Reverb as well as the ‘68 Deluxe. Made to original fender specifications. 120V Primary

• Replacements for Vox Amps
• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".

• Open style, chassis mount transformers with a 115V 60Hz or 50/60Hz primary and an 18V center tapped secondary.

Open style, chassis mount transformers with a 115V 60Hz primary and an 80V center tapped secondary.

Genuine Marshall™ 50 watt power transformer for JCM900.

• Designed for general purpose or replacement use in push-pull or phase inverter tube driver circuits.
• Should not be used for single ended applications. They have no gap for DC bias current present in SE mode.
• Open style with minimum 5" long primary leads.
• Minimum frequency response 150 Hz. - 15 Khz (+/- 1db max. ref. 1 Khz.) at full rated power.
• Core material is Grain Oriented Silicon Steel.

• Primary 115VAC, 50 / 60 Hz., Secondary 115VAC
• Provides complete circuit isolation.
• Electrostatic shield between primary & secondary to greatly attenuate surges and noise.
• Hi-pot tested to 2 KV RMS.
• Circuit breaker in primary.
• Standard 3-wire, grounded plug & receptacle.
• Input (primary) connected to 5 foot long cord & standard North American plug (NEMA 5-15P).
• Output (secondary) connected to 1 foot long "pig tail" cord, 3-wire, standard North American grounded receptacle (NEMA 5-15R).
• North American Mark of Safety - C UL & UL listed (File #E211544)
• Indoor use only
• Remember - These units do NOT convert line frequency

Dual 117/234 VAC primary, 50/60 Hz. operation. 24 V series, 12 V parallel secondary.

Fender® Original Tone Master Power Transformer. Equivalent to #026477.

Specifications:

• Size: 48 VA
• Dual Primary: 117 VAC, 234VAC, 50/60 Hz.
• Secondary VAC RMS Series: 16V @ 3 A
• Secondary VAC RMS Parallel: 8V @ 6 A

Features:

• Primary 117/234 VAC, 50/60 Hz.
• Dual secondaries
• Secondaries can be used as; a center tapped secondary, parallel connected or used individually
• Units are designed for use with all windings engaged.
• Open style.
• Minimum 6" long leads.
• Dual bobbin design - no electrostatic shield required.
• Class B insulation (130 degrees, C) for extra pr

Open style, chassis mount transformers with a 117V 50/60Hz primary and a 12V secondary.

• Replacements for Marshall amps
• Designed for drop in replacement of original units.
• Physically, parts were designed to look similar to original factory units (where possible).
• Material used & design specs. were kept as close as possible to the original part to preserve the stock "tone".