Vacuum Tube Accessories

P-ST8-2000 Socket Saver - 8-Pin with bracket, for reducing wear and tear
8 pin socket saver with bracket. Commonly used in tube testers. Socket savers absorb the main wear and tear from many tube insertions and removals. It's much easier to replace a worn out socket saver than to replace the original socket.
$11.95
P-STABLE Tube Stabilizer - Fender®, Hot Rod Series
Replacement foam tube stabilizer for Fender® Hot Rod Deluxe and Hot Rod Deville amps. This foam block slides over the first two preamp tubes. This genuine Fender® replacement is made in the USA.
$11.95
P-STKY-1 Keyway - Replacement piece for octal tubes
Do you have valuable octal type tubes that work fine except the keyway has been broken off the base? Fix it with this simple and inexpensive product. Simply clean the remainder of the broken keyway from the base and slip one of these on. Will stay on by itself, or you can use a dab of silicon to attach if you wish.
$11.95
package of 4
T-7199-ADT Vacuum Tube Adapter - Use 6GH8A or 6U8A instead of 7199
This adapter allows you to use 6GH8A or 6U8A tubes in place of the difficult-to-find 7199. Tubes are not included.
$12.95
P-YJR Solid State Rectifier - Yellow Jacket® YJR, For 5AR4, 5U4, 5Y3
The YJR is a direct plug-in replacement adapter for use in most amplifiers that use 5AR4/GZ34, 5U4, 5Y3 or similar full-wave rectifier tubes. The YJR converts your amp's vacuum tube rectifier to a solid state rectifier, reducing tube sag for a tighter sound and feel.
$14.95
T-7199-ADT-SET Adapter - use 6GH8A Instead of 7199 tube, 6GH8A Included
Includes:
  • (1) T-7199-ADT
  • (1) T-6GH8A
$15.95
P-TB8-1-2 Terminal Board - one 8 Pin socket, 2 x 6 lugs
Single socket, 2 rows/6 lugs per row, 4 mounting holes. Board dimensions 3" x 3". Terminals are not pre-wired.
$18.95
P-TB9-2-2 Terminal Board - two 9 Pin sockets, 2 x 12 lugs
Dual socket. 2 rows/12 lugs per row, 4 mounting holes. Board dimensions 5 ¼" x 3". Terminals are not pre-wired.
$27.50
P-SAYJ Tube Converter - Yellow Jacket® YJS, for fixed-biased tubes
The YJS is a specialized, current-limiting/voltage-conditioning adapter for use in most 20 to 100 watt amps that use 6L6, EL34, 6550 or 6V6 output tubes. The YJS is for amps with fixed bias power tubes. (Fixed bias tubes have their cathode connected directly to ground and a negative DC voltage applied to their control grid).
$29.95
P-SAYJUNI Tube Converter - Yellow Jacket® YJUni, for low-power amps
The YJUni is a simple pin-converting adapter for use in most amps with 6V6 or similar based tubes like 6F6, 6G6, 6K6, 6Y6, etc. The YJUni is shorter than standard Yellow Jacket® converters. It is designed for use in lower power output amps (20 watts or less) when no power reduction is desired.
$29.95
P-SAYJ-SHORT Tube Converter - Yellow Jacket® YJShort, for reduced-size amps
The YJShort is shorter than the standard YJS converter, allowing for use in amps that do not have room for the standard converters. It is a specialized, current-limiting/voltage-conditioning adapter for use in most 20 to 100 watt amps which use 6L6, EL34, 6550 or 6V6 output tubes
$36.95
SET-TV7-CALIBRATION Vacuum Tube Set - for calibrating TV-7 Testers
This is a set of measured vacuum tubes for use in TV-7 vacuum tube tester calibration. The values for each vacuum tube will be measured and included for the purpose of calibrating your own TV-7 tester at home. Steps for this calibration can be found online. Three tubes will be included:
  • 6L6
  • 6AU6
  • 12AT7

These tubes are tested at the following settings: Tube Filament Settings Bias Shunt Range 6L6 6.3 HS5-3481 23 0 D Tube Filament Settings Bias Shunt Range 6AU6 6.3 ET1-5672 16 0 B Tube Filament Settings Bias Shunt Range 12AT7 12.6 EV7-6080 10 0 C Note that brands are not guaranteed to match photograph.
$75.00