# Associated Merchandising Corp. 126 Schematic

Get a print!
Price: $8.00 In stock  Model: 126 Manufacturer: Associated Merchandising Corp. (AMC) ## Schematic Pages ## Schematics Content: Please note: this content is a computer-generated interpretation of the above schematic and is provided only to help assist you in locating this schematic. For the actual text, please consult the schematic above. Thank you. #### Page 1: AMC PAGE 19-1 ASSOCIATED MERCHANDISING CORP. MODEL 126 '?' - LAMP 47 z 5 ALL asslsrons' wrt ANoALL PAPER cAPAclmRs-zoo vous Sv INLESS OTHERWISE MARKED- 270 .0 3 I.4|| LOOP ASSEMBLY zss z GANG vAmaLE couo. 1 7 _, 2 2 2 7 _, 5 2 loonggi looon m" I.Z$ IST- |>>E TRANSFORMER MFDTQOMFD. 'V Mos mmf Tnmsronlen zo my. w azoo voLuu: sour a smrcn nsov. 8.200 OUTPUT TRANSFORMER 50." 5' PM SPEAKER LINE VOLTAGE: This receiver is designed for operation on 105-125 Volts, 50-60 Cycles, either Alternating or Direct Current (AC-DC) POWER CONSUMPTION: 30 Watts. UNDERWRITER'S LABORATORIES LISTING: This receiver is listed under the Reexamination Service of the Underwriter's Laboratories as indicated by the label attached to the cabinet. TUNING RANGE: Broadcast: 540 to 1650 Kilocycles (180 to 555 meters). DIAL: The Dial Scale is calibrated in Kilocycles. TUBES: The tubes used, and their functions, are as follows: BSS7 R. F. Amplifier IZSQ7 Detector, Avc and Audio Amp. lZSA7 Converter SULGGT Beam Power Amplifier 6557 I. F. Amplifier GSZSGT Rectifier MINOR REASONS FOR FAILURE T0 FUNCTION: Defective tubes: defective Volume Control and On-Oii Switch; line cord reversed on D. C.; defective line cord plug: or tubes in wrong socket. (C)John F. Rider #### Page 2: PAGE 19-2 AMC MODEL 126 ASSOCIATED MERCHANDISING CORP. ALIGNMENT: Should it become necessary at any time to check the alignment of this receiver, proceed as follows: (l) Set the Signal Generator to 455 KC and connect to the grid of the 6SS7 R. F _ Amplifier. or to the Stator Lug on the rear section of the Variable Capacitor. Connect the Signal Generator Ground Lead to a "-B" point underneath the chassis. Connect a suitable output meter across the Speaker Voice Coil Connections. First turn the Volume Control to the maximum position. Turn the Variable Capacitor to the extreme clockwise position. (2) Adjust the trimmers located at the top of the first and second I. F. Trans- formers for maximum output as indicated on the Output Meter. (3) Loosely couple the Signal Generator lead to the Loop and set to 1650 KC. (4) With the Variable Capacitor set at the extreme clockwise position, tune in the 1650 KC signal by means of the Oscillator Trimmer on' the Variable Capacitor (front section). (5) Set the Signal Generator to 1500 KC and turn the Tuning Control so that this frequency is indicated on the dial. Adjust the Antenna Trimmer on the Variable Capacitor (rear section) for maximum output. No other adjustments are necessary. OSC TRmMER/ Ri TRIMMER TRIMMER AND TUBE lOCATION DIAGRAM INSTALLATION: The Model 126 is complete in every detail for efficient and immediate operation. A selfcontained Loop Antenna is included, which
will give excellent results in most locations. Due to the directional properties
of the Loop, it may be advantageous to turn the receiver to the left or right
in noisy locations for maximum signal and minimum noise. A best position
for reception can always be found. In unfavorable locations where distant
reception is required, a well-constructed outside antenna may be used, and
connected to the green wire labeled "Ant." at the rear oi the Loop. A water or
gas pipe may be used as a ground and connected to the black wire labeled
"Gnd." at the rear oi the Loop.

CAUTION: If this receiver is operated on D. C. (Direct Current), and you cannot
obtain reception although the tubes are lighted, reverse the line cord plug to
obtain the correct polarity. Objectionable hum or noise may also be elimi-
nated on A. C. operation by reversing the line cord plug.

(C)John F. Rider

Please note: we carry a wide range of products which will fulfill the specifications above. Please use our search function or browse our products to find what you need!