Atwater Kent 165Q
Model: | 165Q |
Manufacturer: | Atwater Kent |
Schematics Content
Page 1:
Atwater-Kent Mfg. Co.
Model 165-Q, 525-Q
Socket, Trimmer, Parts
Model 165-Q
26809 | Cabinet, less screen |
26679 | Screen |
25745 | Name decalcomania |
25965 | Tone decalcomania |
24278 | Knob (tuning and volume) |
25145 | Knob (tone) |
25022 | Variable condenser |
26727 | Dial assembly |
25692 | Volume control, .5 U |
25004 | Volume control bracket |
24327 | Shield for T5 |
34554 | Shield for T4 includes A5 |
36980 | Tone control and police switch |
25226 | Shaft and blade |
Transformer
Code No. | Part No. | Name of Part |
---|---|---|
T1 | 37080 | No. 1 R.F.T. |
T2 | 37090 | No. 2 R.F.T. |
T3 | 37110 | Osc. T. |
T4 | 37180 | No. 1 I.F.T. |
T5 | 37190 | No. 2 I.F.T. |
T6 | 37150 | Input T. |
Resistors
Code No. | Part No. | Name of Part |
---|---|---|
R1 | 30340 | Red-blue, .1 U, 1/3 W |
R2 | 30390 | Red-bl'k, 20,000 ohm, 1/3 W |
R3 | 30340 | Red-blue, .1 U, 1/3 W |
R4 | 30380 | Red-green, 3,300 ohm, 1/3 W |
R5 | 36430 | Blue-yel., 5,000 ohm, 1/3 W |
R6 | 30370 | Green, 2 U, 1/3 W |
R7 | 31970 | Red-yel., .25 U, 1/3 W |
R8 | 30340 | Red-blue, .1 U, 1/3 W |
R9 | 30360 | Gray-blue, 1 U, 1/3 W |
R10 | 30320 | Maroon, 10,000 ohm, 1/3 W |
R11 | 36240* | Wire wound, 1.03 ohm |
*A no 37220 resistor (1.05 ohm) is supplied with set for use with 3 V dry "A" battery
Condensers
Code No. | Part No. | Name of Part |
---|---|---|
C1 | 31160 | .05 MF, 100 V, NI |
C2 | 31160 | .05 MF, 100 V, NI |
C3 | 33930 | 25 MMF, 500 V |
C4 | 36950 | 730 MMF, 100 V |
C5 | 27630 | .01 MF, 200 V, IND |
C6 | 27630 | .01 MF, 200 V, IND |
C7 | 27630 | .01 MF, 200 V, IND |
C8 | 21160 | 200 MMF, 450 V |
C9 | 29890 | .005 MF, 250 V, IND |
C10 | 22472 | 7 MF, 200 V |
34010 | Multiple by-pass, J15 |
Trimmer Condensers
Code No. | Part No. | Name of Part |
---|---|---|
A4 | 24495 | Single I.F. |
A5 | 31290 | Single I.F. |
A6 | 33080 | Single I.F. |
Sockets
Part No. | Name of Part |
---|---|
24494 | 6 prong |
24492 | 4 prong |
25196 | Speaker |
165-Q Speaker No. 37170
525-Q Speaker No. 39200
Part No. | Name of Part |
---|---|
26874 | Cable and plug assembly (525-Q) |
26755 | Cable and plug assembly (165-Q) |
27128 | Magnet |
27129 | Magnet clamping plate |
8188 | 8/32 hex. nut |
9898 | No. 6 lock washer |
23318 | No. 2 washer |
27138 | Clamping block top |
27139 | Clamping block bottom |
27141 | Adjusting screw, 6/32 |
27142 | Cover plate |
27143 | Mounting bracket |
27144 | Sound unit assembly, less magnets |
27145 | Conehead assembly |
27146 | Coil |
27147 | Armature |
27211 | Mount. brackets, pair (525-Q) |
27148 | Spring |
27149 | Terminal |
Model 525-Q
(For parts not listed below refer to Model 165-Q parts list)
Part No. | Name of Part |
---|---|
26565 | Variable condenser assembly |
27305 | Knob shaft |
27450 | Osc. T (T3) |
26719 | Dial light socket |
26722 | Battery cable with resistor |
26519 | Dial assembly |
26721 | Dial lamp (air cell, 2 V, 60 MILS) |
26642 | Base cover |
26569 | Knob (tuning and volume) |
26571 | Knob (tone) |
36250* | Wire wound, 1.15 ohm (R11) |
26669 | Shipping container |
26545 | Escutcheon nameplate |
25691 | Escutcheon window |
26718 | Volume control, .5 U |
37490 | Tone control switch |
26573 | Shaft and blade |
* A No. 37130 resistor (1.15 ohm) is supplied with set for use with a 3 V dry "A" battery.
Speaker Adjustment: When adjustment is required, put the set and speaker in operation and tune in a signal. Loosen screw A and tighten B, or vice versa, in order to center the armature in the magnet gap. If the armature is not correctly centered, it may strike against one pole of the magnet and cause chattering. If the speaker overloads or chatters only on a very strong signal, turn screw C anti-clockwise. This tightens the armature movement. (In general it is not advisable to disturb the adjustment of screw C.)
Page 2:
Atwater Kent Mfg. Co.
Model 168Q, 528Q
Schematic
Voltage
Total "B" voltage at time measurements were made equaled 135 volts. Tube voltages are taken from -F of each tube, using the 250 volt scale of a 1000 ohm per volt meter. Resistor R11 is used with 2 volt air cell, but is not used with 2 volt storage cell. In model 525Q a 2 volt air cell dial light (80 mils) is connected across the filament circuit.