You are here

Project Lists

Pages

Copied from cart on 05/27/2019
8 items in this list
Challenger CH18
Re Cap, New 1/4" Jacks, 3 Prong Power cord
13 items in this list
Model REP CRO-46287 Radio Receiver Dept of Navy
I was fortunate enough to find this at a Flea Market while on vacation in Branson Mo in September 2019. I have always been fond of Tube equipment from a very young age, and as a 30 plus year electronics hobbyist a 20 plus year Industrial Electrician and more recently a 2 plus year Licensed Amateur Radio operator.
1 items in this list
Tube tester
Restoring a Simpson Model 1000 tube tester.
2 items in this list
Philco
Australian Philco AM radio
8 items in this list
zenith 6s254
This project is NOT a restoration. it is a repair and maintain with "some modern" components to get it functioning so it can be enjoyed for many years to come.
2 items in this list
Fender Tweed Clone Amp Projects
Various Fender Tweed 5F2A, and 5E3 Tweed Deluxe Projects. Also will be including a 1956 Silvertone Hi-Fi single ended amp conversion from a reel to reel tape recorder. Feel free to contact me with questions and comments regarding these projects.
2 items in this list
Fender 6G6-B Bassman
Fender Blonde 6G6-B Bassman build for a client. Chassis (zachmdhunter - eBay), faceplate (zachmdhunter - eBay), power transformer (Classic Tone 40-18005), output transformer (Classic Tone 40-18009), and choke (Classic Tone 40-18003) will be sourced outside of AES. This will be a "chassis only" build. Had to substitute 500V filter caps for the 600V's called for in the schemo as the 600s do not fit in the doghouse.
50 items in this list
3 Position Tele Electronics Upgrade
Here's everything you need to upgrade the electronics in your Tele. The pots will fit the American Tele plates. If you need the plate you can find it here: https://www.tubesandmore.com/products/control-plate-fender-vintage-telecaster-chrome The one in the photo was finished up with some heat shrink for a pro look. If you want to add the heat shrink but don't already have some it's available here: https://www.tubesandmore.com/products/heat-shrink-assorted-diameters-6-long-23-pieces
6 items in this list
Treble Bleed
This is a really simple mod that can be added to most guitars. The circuit is used to brighten up guitars that darken the tone as the volume is rolled off giving more clarity to the signal during the full sweep of the pot. It's easy to install and can be further tweaked by playing with the resistor and capacitor values. A carbon comp resistor was chosen for a classic look but any type will work.
2 items in this list
RCA 45-EY-2 Capacitors
Capacitors required for RCA 45-EY-2 Victrola amplifier. May substitute C-ER47-80-160 "Firecracker" for the two electrolytic capacitors for a more "authentic" look. Also, the 82pf Silver Mica capacitor probably doesn't need to be replaced.
7 items in this list
3 Position Tele Electronics Upgrade w/ Treble Bleed
Here's everything you need to upgrade the electronics in your Tele and add the treble bleed mod. The pots will fit the American Tele plates. If you need the plate you can find it here: https://www.tubesandmore.com/products/control-plate-fender-vintage-telecaster-chrome The one in the photo was finished up with some heat shrink for a pro look. If you want to add the heat shrink but don't already have some it's available here: https://www.tubesandmore.com/products/heat-shrink-assorted-diameters-6-long-23-pieces
8 items in this list
Knight 10W amp
Restoring and converting a Knight-kit 10 watt amplifier into a guitar amp.
15 items in this list
Copied from cart on 12/27/2019
14 items in this list
Vibrolux Reverb Amp
Chassis clone of BF Vibrolux Reverb Amp
39 items in this list
Hallicrafters WR-600 Recap
Recapping and installing a line isolation transformer on used radio. Purchased on eBay for $41.00 plus shipping and tax. So not spending a lot on it, yet.
11 items in this list
Zenith M/N 10S464 S/N S712471
My first restoration project on a 1940 Zenith Model 10S464 Serial Number S-712471
8 items in this list
Hallicrafters S19R
Hallicrafters S19R Sky Buddy Receiver
8 items in this list
EMC-206
EMC-206 Tube Tester https://www.dropbox.com/s/me3ps5uu7p0cc85/emc_206_tube_tester_operating_instructions.pdf
1 items in this list
Custom mk3
Custom two channel 15W guitar tube amplifier. The first channel has classic scheme with two 12AX7 tubes and Baxandall tone stack (Ampeg). The second channel is EF86 Vox like stage with one knob tone stack. Output stage is classic push pull with two EL84 tubes.
17 items in this list
Copied from cart on 04/27/2019
25 items in this list
Parts for creating a Strat loaded pick guard.
12 items in this list
Copied from cart on 09/10/2019
4 items in this list
Copied from cart on 12/12/2019
10 items in this list
Tektronix Type B
Plug in for Tektronix Scope Clean up and test.
3 items in this list
First tube electronic build
28 items in this list
Telefunken Concertino Model 5093W
Restore Telefunken Concertino Model 5093W
7 items in this list
Waterman S10 Pocketscope
Waterman S10 Pocketscope 2AP1A CRT Schematic: https://www.dropbox.com/s/wa2w4xk74i4h2xv/Waterman_S10A.pdf?dl=0
3 items in this list
This is most of the parts you'd need beyond the small parts (resistors & small capacitors) option with a Triode Electronics turret board. This list also includes upgraded Atom caps to replace the lower end ones that Triode supplied with my kit. This doesn't include a chassis, cabinet, transformers and hookup wire.
18 items in this list
Single Ended EL84 on 12x8x2
39 items in this list
Bob Heil's Pine Board Project Power Supply
12 items in this list
Guitar Project - Ibanez (Gibson knockoff)
This 80's Ibanez I've had for about 10 years and it's never worked due to bad electrical. I bought it off a coworker for 80 bucks. He was the original owner too! And yes, that case is original. The guitar has been sitting in my collection for a looong time and now it's time to raise it from the dead. I'm gutting the original wiring and replacing it with my own diagram. I'm not using any pots or resistors or capacitors. I'm just wiring the pickup straight to the jack using a terminal strip.
1 items in this list
rebuild westinghouse mocha h-437t5a/h-675t5
3 items in this list
Copied from cart on 02/05/2020
10 items in this list
This is Dave Hunter's design from his book "The Guitar Amp Handbook". "This is a true Class A amp. The base-design is built around a pair of 6v6 output tubes. The way these tubes are individually cathode-biased means you can use a wide range of output tube configurations. Both 6v6's for 8 watts, one 6v6 for 4 watts, a single 6L6 for 8 watts, a single EL34 or KT66 for about 9 or 10 watts, a single 6K6 for a soft 3 watts, and even more octal output tubes are compatible with this design. See the book for instructions and pics. Also a great book for beginners and amp building enthusiasts.
30 items in this list
Taking a vintage Westinghouse meter box and making a practice tube guitar amp out of it.
32 items in this list
Fender Champ
An easy restore of a Fender Champ amplifier. New tubes, multi cap and general cleaning/lube of pots. All original down to the red tag on the power cord and warranty card.
4 items in this list
fender reverb using 12au7 to replace 6k6/transformer http://www.valvewizard.co.uk/reverbdriver.html
16 items in this list
The 'Lil 7
10 items in this list
Repair of audio mixer
1 items in this list
Simple champ guitar amp with B+ boost supply (no power transformer or rectifier tube) and DC series filaments.
2 items in this list
replace electrolytic capacitors in A0-28 preamp for A-100 series, B-3, C-3, D-100 series, RT-3. C56 40/450, C57 40/400, C58 30/350 in one can. C59 (C56 TYPO ON SCHEMATIC) 10/350, C9 30/25, C26 30/25 in one can. C30 25/25 axial lead. schematic http://captain-foldback.com/Hammond_sub/schematics/ao28.jpg Capacitor and resistor list http://www.hammondb3organ.net/a028parts.php
3 items in this list
Precision Electronics S35
PA To guitar amp conversion.
5 items in this list
Copied from cart on 12/27/2019
17 items in this list
fada 895 amp
Output amp for FADA TV project, missing output stage.
6 items in this list
4 Position Tele Electronics Upgrade
Here's everything you need to upgrade the electronics in your Tele with a 4 position switch. The first three positions are the same as the 3 position switch and the 4th position is the fatter sounding series position. The pots will fit the American Tele plates. If you need the plate you can find it here: https://www.tubesandmore.com/products/control-plate-fender-vintage-telecaster-chrome The one in the photo was finished up with some heat shrink for a pro look.
6 items in this list
Restore 1967 Fender Bandmaster head
1 items in this list
Restoration of Motorola 58R11 AA5 tube radio. First project!
7 items in this list
Copied from cart on 06/04/2019
31 items in this list
Audio Output
2 items in this list

Pages